//-------------------TIM2.c------------------------//
#include "timer.h"
#include "led.h"
//通用定時器中斷初始化,這里時鐘選擇為APB1的2倍，而APB1為36M,
//arr：自動重裝值。
//psc：時鐘預分頻數
//這里使用的是定時器2
void Timerx_Init(u16 arr,u16 psc)
{
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
NVIC_InitTypeDef NVIC_InitStructure;
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); //時鐘使能
TIM_TimeBaseStructure.TIM_Period = 5000; //設置在下一個更新事件裝入活動的自動重裝載寄存器周期的值 計數到5000為500ms
TIM_TimeBaseStructure.TIM_Prescaler =(7200-1); //設置用來作為TIMx時鐘頻率除數的預分頻值 10Khz的計數頻率
TIM_TimeBaseStructure.TIM_ClockDivision = 0; //設置時鐘分割:TDTS = Tck_tim
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //TIM向上計數模式
TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure); //根據TIM_TimeBaseInitStruct中指定的參數初始化TIMx的時間基數單位
TIM_ITConfig( //使能或者失能指定的TIM中斷
TIM2, //TIM3
TIM_IT_Update | //TIM 中斷源
TIM_IT_Trigger, //TIM 觸發中斷源
ENABLE //使能
);
NVIC_InitStructure.NVIC_IRQChannel = TIM2_IRQn; //TIM3中斷
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; //先占優先級0級
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3; //從優先級3級
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能
NVIC_Init(&NVIC_InitStructure); //根據NVIC_InitStruct中指定的參數初始化外設NVIC寄存器
TIM_Cmd(TIM2, ENABLE); //使能TIMx外設
}
void TIM2_IRQHandler(void) //TIM2中斷
{
if (TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET) //檢查指定的TIM中斷發生與否:TIM 中斷源
{
TIM_ClearITPendingBit(TIM2, TIM_IT_Update ); //清除TIMx的中斷待處理位:TIM 中斷源
LED0=!LED0;
}
}
//-------------------TIM2.H------------------------//
#ifndef __TIMER_H__
#define __TIMER_H__
#include "sys.h"
void Timerx_Init(u16 arr,u16 psc); //通用定時器2中斷初始化,這里時鐘選擇為APB1的2倍，而APB1為36M
void TIM2_IRQHandler(void); //TIM2中斷
#endif