欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136

標題: 51單片機舞蹈機器人仿真+程序 [打印本頁]
作者: Daoist    時間: 2017-6-18 15:30
標題: 51單片機舞蹈機器人仿真+程序
仿真原理圖如下（proteus仿真工程文件可到本帖附件中下載）


單片機源程序如下:
  1. #include "reg51.h"
  2. #include "intrins.H"
  3. //8步式步進電機脈沖序列
  4. //unsigned char steps[8] = {0x77,0x33,0xbb,0x99,0xdd,0xcc,0xee,0x66};
  5. unsigned char steps[8] = {0x2,0x6,0x4,0xc,0x8,0x9,0x1,0x3};
  6. //當前各電機在上述序列中的位置
  7. unsigned char cur_step[8] = {0,0,0,0,0,0,0,0};
  8. //這個文件用于記錄舞步信息序列
  9. char speed_tickers[8] = {0,0,0,0,0,0,0,0};
  10. //從上述文件中讀出的當前舞步信息
  11. unsigned char speeds[8] = {0,0,0,0,0,0,0,0};
  12. unsigned char data_pointer = 0;//指向舞步數據的指針
  13. unsigned char time_t = 0;//指定重新讀取一次 speeds 值的計時周期
  14. code char dancedata[] = {54,15,12,12,87,95,65,45,-89,-88,-54,-54,54,68,-45,-65,-65,-48,101,121,115,117,19,
  15. -98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,109,104,-30,-102,-104,-106,110,100,
  16. 54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,
  17. 100,130,30,10,-90,-120,87,102,102,100,130,30,10,-90,-120,87,102,103,105,54,15,12,12,87,95,65,45,-89,-88,-54,
  18. -98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,
  19. -98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,109,104,-30,-102,-104,-106,110,
  20. 100,130,30,10,-90,-120,87,102,102,100,130,30,10,-90,-120,87,-120,87,102,103,105,109,104,-30,-102,-104,-106,110,
  21. 54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,
  22. 54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,
  23. 54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,
  24. 54,15,12,12,87,95,65,45,-89,-88,-54,-54,-98,95,102,102,100,130,30,10,-90,-120,87,102-114,-101,-24,-98,95,102,102,
  25. -98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,
  26. -98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,
  27. -98,-100,-21,-114,-101,-24,-98,95,102,102,100,130,30,10,-90,-120,87,102,103,105,12,87,95,65,45,-89,-88,-54,
  28. };
  29. code char pin[8] = {1,2,4,8,16,32,64,128};
  30. char MAX_SPEED_TICKER = 120;
  31. unsigned char i; //電機序號

  33. void InitTimer(void) //初始化計數器
  34. {
  35.   TH0 = 0xFA;  //設置觸發周期:1000次
  36.   TL0 = 0x24;
  37.   TMOD = TMOD |0x01;  //select mode 1
  38.   TR0 = 1; //start timer0
  39.   ET0 = 1; //enable timer 0 interrupt
  40.   EA =1; //global interrupt enable
  41. }

  43. void SetAllSpeeds(void)  //設置各電機的速度,并讓它運動起來
  44. {
  45.   char delta;  //旋轉方向 1:正 -1:反  0:停
  46.   for(i=0;i<8;i++)
  47.   {
  48.     P2=pin[i]; //發送鎖存信號
  49.     speed_tickers[i] += speeds[i]; //計數值增加 speed[i]越高,增加得越多
  50.     if(speed_tickers[i] >= MAX_SPEED_TICKER) //如果計數值超過預定最大值,就發送脈沖
  51.     {
  52.       speed_tickers[i] = 0;
  53.       delta = 1;
  54.     }
  55.     else if(speed_tickers[i] <= -MAX_SPEED_TICKER) //同上,反響旋轉
  56.     {
  57.       speed_tickers[i] = 0;
  58.       delta = -1;
  59.     }
  60.     else delta = 0;
  61.     cur_step[i] += delta;
  62.     cur_step[i] &= 0x07; //計算當前應發脈沖
  63.     P0 = steps[cur_step[i]];
  64.     P2 = 0;
  65.   }
  66. }

  68. void OnTimer(void) interrupt 1 using 2
  69. {
  70.   unsigned char j;
  71.   SetAllSpeeds();
  72.   InitTimer();
  73.   time_t++;
  74.   if(time_t==200) //每200次觸發讀取一次新舞步數據
  75.   {
  76.     for(j=0;j<8;j++)
  77. ……………………

  79. …………限于本文篇幅 余下代碼請從51黑下載附件…………
復制代碼

所有資料51hei提供下載:
舞蹈機器人步進機仿真，C51程序通過.rar (49.12 KB, 下載次數: 71)



作者: sus30    時間: 2017-11-24 19:47
正在找，多謝分享
作者: xxmv99    時間: 2017-11-24 21:43
這個有點厲害了，支持。~
作者: ltx    時間: 2018-10-24 19:52
牛皮的操作
作者: Sinclair！    時間: 2018-11-5 18:44
正想試試，參考一哈
作者: cccxxx77    時間: 2025-4-22 16:16
正在找，多謝分享



歡迎光臨 (http://www.raoushi.com/bbs/) Powered by Discuz! X3.1