標題: 基于VB實現單片機控制步進電機有了單片機的程序，誰會VB的編程 [打印本頁]
作者: guoxin123 時間: 2015-5-6 10:17
標題: 基于VB實現單片機控制步進電機有了單片機的程序，誰會VB的編程
#include "reg52.h"
#include "INTRINS.H"
#include <absacc.h>
#include <math.h>
#define uint unsigned int
#define uchar unsigned char
void check_addr(void); /*地址核對*/
uchar code slave_addr[4]={00, 01, 02, 255}; /*從機地址*/
uchar idata T0low, T0high,common_count,input_order,cmd_in_permit,interval; uchar sent_ok,speed_change,start_up,start_end,address_true,i;
uint y1;
uint code add[100]={60006,62771,63693,64154,64430,64614,64746,64845,64922,64983,65033,65075,65111,65141,65167,65190,65211,65229,65245,65260,65273,65285,65296,65306,65315,65323,65331,65339,65345,65352,65358,65363,65368,65373,65378,65382,65387,65390,65394,65398,65401,65404,65407,65410,65413,65416,65418,65421,65423,65425,65428,65430,65432,65434,65435,65437,65439,65441,65442,65444,65445,65447,65448,65450,65451,65452,65453,65455,65456,65457,65458,65459,65460,65461,65462,65463,65464,65465,65466,65467,65468,65469,65469,65470,65471,65472,65472,65473,65474,65475,65475,65476,65477,65477,65478,65478,65479,65480,65480,65481};
sbit P2_0=P2^0; /*作輸入步進電機的脈沖信號發送口*/
sbit P2_2=P2^2; /*作輸入步進電機的旋轉方向信號發送口*/
sbit P1_0=P1^0; /*作串口輸出信號的使能口, P1_0=0時接通串口,輸出信號*/
sbit WD=P1^7; /*看門狗*/
main()
{ P2_0=0;
P2_2=0; /*步進電機的旋轉方向待試驗后確定*/
P1_0=1; /*開機時需要關斷,串口發送功能,需要時再接通*/
WD=1; /*看門狗先為1，電平翻轉為喂狗*/
i=0;
common_count=0;
cmd_in_permit=0;
input_order=0;
interval=0;
address_true=1;
speed_change=0;
start_up=0;
start_end=0; sent_ok=0; //允許發送
EA=1; /*開放總中斷*/
TMOD=0x21;
TH1 = 0xFD; // 波特率9600
TL1 = 0xFD;
SCON = 0xd0; // 設定串行口工作方式
PCON &= 0x00; // 波特率不倍增
SM2=1;
TR1 = 1;
ES=1; // 啟動定時器1
T2MOD=00;
T2CON=0x00;
RCAP2H =0xEE; //賦T2的預置值0xA600,25MS，0xB800，20MS,0xCA00，15MS,0xDC00，10MS，0xEE00，5MS RCAP2L =0x00;
TR2=1; //啟動定時器
ET2=1; //打開定時器2中斷
do {
if(address_true==1)
{
address_true=0; check_addr();
}
if(start_up==1&&start_end==0) //第一次啟動
{
y1=add[common_count];
T0high = (uchar)(y1>>8) ; /*取y1的高8位*/
T0low = (uchar)(y1&0x00ff); /*取y1的低8位*/
TR0 = 1; ET0=1; /*允許T/C0中斷*/
start_end=1;
}
if(speed_change==1)
{
if(interval>=0&&interval<=0x63)
{
if(interval>common_count)
{
common_count=common_count+1;
}
if(interval<common_count)
{
common_count=common_count-1;
}
}
speed_change=0;
}
if(sent_ok==1)
{
sent_ok=0;
P1_0=0;
for(i=0;i<=20;i++) {_nop_();}
TI=0; SBUF=T0high;
while(TI==0);TI=0;
TI=0; SBUF=T0low;
while(TI==0);TI=0;
P1_0=1;
for(i=0;i<=20;i++) {_nop_();}
SM2=1;
}
}
while(1);
}
void timer0(void) interrupt 1 using 3
{
P2_0=~P2_0;
y1=add[common_count];
T0high = (uchar)(y1>>8); /*取y1的高8位*/
T0low = (uchar)(y1&0x00ff); /*取y1的低8位*/
TH0=T0high; /*高8位T0high送定時器0的TH0*/
TL0=T0low; /*低8位T0low送定時器0的TL0*/ }
void timer2(void) interrupt 5 using 2 {
TF2=0; /*T2溢出中斷需軟件清0*/
speed_change=1; //速度可以改變標示，以便主程序處理
WD=!WD; /*MAX813喂狗*/
}
void inte_SERIAL() interrupt 4 using 1 /*串口0中斷服務子程序*/
{
uchar key_in key_in=0;
if(RI)
{
key_in=SBUF;
RI=0;
if (SM2==1)
{
if(key_in==slave_addr[2])
{
SM2=0;
address_true=1;
}
}
if ((SM2==0)&& (RB8==0))
{
if(key_in==0xff){SM2=1;
}
if(key_in==0xfe)
{ /*接收主機命令引導字節，準備接收主機命令*/
cmd_in_permit=1;
}
if(cmd_in_permit==1)
{ input_order=input_order+1; }
if (input_order==2) { /*接收主機命令，使從機開始調節電機*/
cmd_in_permit=0;
input_order=0; /*interval代表控制器發給電機的轉速期望值*/
interval= key_in;
sent_ok=1;
if(start_up==0){start_up=1;
}
}
}
}
}
void check_addr(void)
{ /*地址核對成功，發送從機地址給主機*/
TB8=1;
RB8=0;
P1_0=0;
for(i=0;i<=25;i++) {_nop_();}
SBUF=slave_addr[2]; /*發送地址核對成功，發送從機地址給主機*/
do{} while(TI==0); TI=0;
P1_0=1;
for(i=0;i<=25;i++) {_nop_();}
TB8=0;
}
| 歡迎光臨 (http://www.raoushi.com/bbs/) |
Powered by Discuz! X3.1 |