欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136

標題: Arduino控制RadioShack Pro-405 MB1501仿真源碼與實踐(寬頻接收機改造) [打印本頁]
作者: learningone    時間: 2018-11-25 09:40
標題: Arduino控制RadioShack Pro-405 MB1501仿真源碼與實踐(寬頻接收機改造)
本人的Pro-405 寬頻接收機部分按鍵無效，顯示看不清楚，出差改了這個程序，29-54/87.3-107.9/137-174/380-512MHz 基本步進均為12.5kHz，可選50/100kHz,有W/NFM切換控制，未做波段控制。29-54可接電視高頻頭中頻，87.3-107.9可有可無，音質一般，380-512本地還能收到幾套模擬伴音，歡迎各位改進。
MB1501_Scanner.ino 副本(2)V0.1直接計算參數，副本采用遞加遞減，仿真長按F+，發送間隔均為111ms，主要取決于按鍵延時100ms。V0.2按鍵延時可變，仿真長按F+，發送間隔約為21ms。
Arduino無法直接輸入中文，有簡單英文說明，引用部分保留日文注釋。
Pro-405.xls為相關參數計算，其中380MHz 4F應為50，難道是WPS的問題？

MB1501仿真原理圖如下（proteus仿真工程文件可到本帖附件中下載）


MB1501引腳圖與管腳功能定義：

MB1501的arduino源程序如下:
  1. /*
  2. QRP 2m FM Transceiver Project with BS2 shiftout any bits
  3. modify by learning 2016.11 V0.2 fast scan */
  4. //RadioShack Pro-405 29-54/87.3-107.9/137-174/380-512MHz with 12.5kHz steps
  5. #include<stdlib.h>
  6. #include <LiquidCrystal.h>
  7. LiquidCrystal lcd(2, 3, 4, 5, 6, 7);
  8. int buttonpin = A3;
  9. int audiopin = A2;
  10. const int PLL_data = 8 ;
  11. const int PLL_clock = 9 ;
  12. const int PLL_LE = 10 ;

  14. //unsigned int  R_up = 0x84 ;  //M=64 R=512
  15. unsigned int  R_up = 0x88 ;  //M=64 R=1024
  16. unsigned int  R_low = 0x01 ;
  17. unsigned int  N_up = 0;
  18. unsigned int  N_low;
  19. unsigned int A_0; //A0 A' can't be used
  20. unsigned int A;
  21. int T = 100;

  23. char* audiotext[]={
  24.   "NFM", "WFM"};
  25. int audio = 0;
  26. long freqbandarray[] = {
  27.   873000, 290000, 1370000, 3800000};//0.1kHz
  28. char* bandtext[]={
  29.   "FM", "VL", "VH", "U"};
  30. int band = 1;
  31. long stepsizearray[] = {
  32.   125 ,500 ,1000 ,80000};//0.1kHz
  33. char* stepsizetext[]={
  34.   "12.5 kHz", "50 kHz", "100 kHz", "8 MHz"};
  35. int stepsize = 0;
  36. int button;
  37. int buttondelay = 0;
  38. int menuoption = 0;

  40. void pll_set_frequency(long pllfreq) {
  41.   if (band == 0 || band == 1) {
  42.     N_low=((pllfreq+107000)/8000);
  43.     A=(freqbandarray[band]+107000)/125%64;
  44.   }
  45.   if (band == 2 ) {
  46.     N_low=((pllfreq-107000)/8000);
  47.     A=(freqbandarray[band]-107000)/125%64;
  48.   }
  49.   if (band == 3) {
  50.     N_up=highByte((pllfreq-107000)/8000);
  51.     N_low=lowByte ((pllfreq-107000)/8000);
  52.     A=(freqbandarray[band]-107000)/125%64;
  53.   }
  54.   A_0 = A << 1;

  56.   //M,Rを設定
  57.   digitalWrite(PLL_LE, LOW);
  58.   // シフト演算を使ってデータを送信する
  59.   shiftOut(PLL_data, PLL_clock, MSBFIRST, R_up);
  60.   shiftOut(PLL_data, PLL_clock, MSBFIRST, R_low);
  61.   digitalWrite(PLL_LE, HIGH);

  63.   //N,Aを設定   
  64.   digitalWrite(PLL_LE, LOW);
  65.   // シフト演算を使ってデータを送信する
  66.   shiftOut(PLL_data, PLL_clock, MSBFIRST, N_up);
  67.   shiftOut(PLL_data, PLL_clock, MSBFIRST, N_low);
  68.   shiftOut(PLL_data, PLL_clock, MSBFIRST, A_0);
  69.   digitalWrite(PLL_LE, HIGH);
  70. }

  72. void readbuttons(){
  73.   int pinread = analogRead(buttonpin);
  74.   if (pinread > 90 && pinread < 120) { //1k 1k2
  75.     buttondelay ++;
  76.     if (buttondelay == 2) button = 0;//M-
  77.     else button = -1;
  78.   }
  79.   if (pinread > 190 && pinread < 230) { //2k4 2k7
  80.     buttondelay ++;
  81.     if (buttondelay == 2) button = 1;//M+
  82.     else button = -1;
  83.   }
  84.   if (pinread > 320 && pinread < 360) { //4k7 5k1
  85.     button = 2;//--
  86.     //delay (100);//ms
  87.     delay (T);
  88.     buttondelay ++;
  89.     if (buttondelay == 2) {
  90.       button = 4;
  91.       T=10;
  92.     } //-
  93.   }
  94.   if (pinread > 480 && pinread < 540) { //10k
  95.     buttondelay ++;
  96.     if (buttondelay == 2) { //BAND
  97.       band ++;
  98.       if (band > 3) band = 0;
  99.       if (band == 0 || band == 1) {
  100.         A=(freqbandarray[band]+107000)/125%64;
  101.         R_up = 0x88;
  102.         N_up = 0;
  103.       }
  104.       if (band == 2) {
  105.         A=(freqbandarray[band]-107000)/125%64;
  106.         R_up = 0x88;
  107.         N_up = 0;
  108.       }
  109.       if (band == 3) {
  110.         A=(freqbandarray[band]-107000)/125%64;
  111.         R_up = 0x98;
  112.       }
  113.       //setfrequency();//?
  114.       pll_set_frequency(freqbandarray[band]);
  115.       delay (30);//ms
  116.     }
  117.   }
  118.   if (pinread > -1 && pinread < 40) {
  119.     button = 3;//++
  120.     //delay (100);//ms
  121.     delay (T);
  122.     buttondelay ++;
  123.     if (buttondelay == 2) {
  124.       button = 5;
  125.       T=10;
  126.     } //+
  127.   }
  128.   if (pinread > 1000) {
  129.     buttondelay = 0;
  130.     T=100;
  131.     button = -1;
  132.   }
  133. }

  135. void menu(){
  136.   if (button == 1) menuoption ++;
  137.   if (button == 0) menuoption --;
  138.   if (menuoption > 2 ) menuoption = 0;
  139.   if (menuoption < 0 ) menuoption = 2;
  140.   if (menuoption == 0) setfrequency();
  141.   if (menuoption == 1) setstepsize();
  142.   if (menuoption == 2) setaudio();
  143. }

  145. void setfrequency(){
  146.   lcd.setCursor(0, 0);
  147.   lcd.print("frequency  ");
  148.   //  lcd.print("FREQ  ");
  149.   lcd.setCursor(0, 1);
  150.   if (button == 2) {
  151.     freqbandarray[band] = freqbandarray[band] - (stepsizearray[stepsize]);
  152.     if (band == 0 && freqbandarray[band] < 873000) {
  153.       freqbandarray[band] = 1079000;
  154.       A=(freqbandarray[band]+107000)/125%64;
  155.     }
  156.     if (band == 1 && freqbandarray[band] < 290000) {
  157.       freqbandarray[band] = 540000;
  158.       A=(freqbandarray[band]+107000)/125%64;
  159.     }
  160.     if (band == 2 && freqbandarray[band] < 1370000) {
  161.       freqbandarray[band] = 1740000;
  162.       A=(freqbandarray[band]-107000)/125%64;
  163.     }
  164.     if (band == 3 && freqbandarray[band] < 3800000) {
  165.       freqbandarray[band] = 5120000;
  166.       A=(freqbandarray[band]-107000)/125%64;
  167.     }
  168.     pll_set_frequency(freqbandarray[band]);
  169.   }
  170.   if (button == 3) {
  171.     freqbandarray[band] = freqbandarray[band] + (stepsizearray[stepsize]);
  172.     if (band == 0 && freqbandarray[band] > 1079000) {
  173.       freqbandarray[band] = 873000;
  174.       A=(freqbandarray[band]+107000)/125%64;
  175.     }
  176.     if (band == 1 && freqbandarray[band] >= 540000) {
  177.       freqbandarray[band] = 290000;
  178.       A=(freqbandarray[band]+107000)/125%64;
  179.     }
  180.     if (band == 2 && freqbandarray[band] >= 1740000) {
  181.       freqbandarray[band] = 1370000;
  182.       A=(freqbandarray[band]-107000)/125%64;
  183.     }
  184.     if (band == 3 && freqbandarray[band] > 5120000) {
  185.       freqbandarray[band] = 3800000;
  186.       A=(freqbandarray[band]-107000)/125%64;
  187.     }
  188.     pll_set_frequency(freqbandarray[band]);
  189.   }
  190.   lcd.print((freqbandarray[band]) / 10000);
  191.   lcd.print (".");
  192.   if (((freqbandarray[band]) % 10000) <1000) {
  193.     lcd.print("0");
  194.     if (((freqbandarray[band]) % 10000) == 0) lcd.print("000");
  195.     else lcd.print((freqbandarray[band]) % 10000);
  196.   }
  197.   else lcd.print((freqbandarray[band]) % 10000);
  198.   lcd.print(" MHz    ");
  199. }  

  201. void setstepsize(){
  202.   lcd.setCursor(0, 0);
  203.   lcd.print("stepsize        ");
  204.   lcd.setCursor(0, 1);
  205.   if (button == 4) stepsize --;
  206.   if (button == 5) stepsize ++;
  207.   if (stepsize < 0) stepsize = 2;
  208.   if (stepsize > 2) stepsize = 0;
  209.   lcd.print(stepsizetext[stepsize]);
  210.   lcd.print("             ");
  211. }  

  213. void setaudio(){
  214.   lcd.setCursor(0, 0);
  215.   lcd.print("audio           ");
  216.   lcd.setCursor(0, 1);
  217.   if (button == 4) audio --;
  218.   if (button == 5) audio ++;  
  219.   if (audio < 0) audio = 1;
  220.   if (audio > 1) audio = 0;
  221.   lcd.print(audiotext[audio]);
  222.   lcd.print("            ");
  223.   digitalWrite(audiopin, audio);
  224. }


  227. void setup(){
  228.   pinMode(audiopin, OUTPUT);
  229.   pinMode(PLL_data, OUTPUT);//!
  230.   pinMode(PLL_clock, OUTPUT);
  231.   pinMode(PLL_LE, OUTPUT);
  232.   lcd.begin(16, 2);
  233.   //setfrequency();//?
  234.   pll_set_frequency(freqbandarray[band]);
  235.   delay (30);//ms
  236.   digitalWrite(audiopin, audio);
  237. }


  240. void loop(){
  241.   readbuttons();
  242.   menu();
  243. }

復制代碼


所有資料51hei提供下載:
MB1501_Scanner.7z (293.18 KB, 下載次數: 17)






歡迎光臨 (http://www.raoushi.com/bbs/) Powered by Discuz! X3.1