1024手机基地看电影,午夜福利视频导航,国产精品福利在线一区,亚洲欧美日韩另类成人,在线观看午夜日本理论片,成年超爽免费网站,国产精品成人免费,精品动作一级毛片,成人免费观看网站,97精品伊人久久大香蕉

標題: 基于51板子得貪吃蛇游戲，想知道哪錯了，謝謝 [打印本頁]

作者: lynn710 時間: 2018-8-13 19:57
標題: 基于51板子得貪吃蛇游戲，想知道哪錯了，謝謝
本帖最后由 lynn710 于 2018-8-13 20:01 編輯

急用，多謝指正
#include"reg52.h"
#include "intrins.h"

sbit RS=P2^6; //并行的指令/數據選擇信號, H數據, L命令
sbit RW=P2^5; //并行讀寫選擇信號, H讀, L寫
sbit E=P2^7; //并行使能端, H有效, L無效
sbit PSB=P3^2; //并/串接口選擇, H并,L串
sbit RET=P3^4; //復位, L有效
#define  LcdData P0
unsigned char Check_Busy(void);
void Lcd_WriteData(unsigned char);
unsigned char Lcd_ReadData(void);
void Lcd_WriteCmd(unsigned char);
void Lcd_PutPixel(unsigned char,unsigned char,unsigned char);
unsigned char Lcd_ReadPixel(unsigned char,unsigned char);
void Lcd_HoriLine(unsigned char,unsigned char,unsigned char Length,unsigned char Color);
void Lcd_VertLine(unsigned char x,unsigned char y,unsigned char Length,unsigned char Color);
void Lcd_Line(unsigned char x1,unsigned char y1,unsigned char x2,unsigned char y2,unsigned char Color);
void Lcd_Rectangle(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char Color);
void Lcd_Circle(unsigned char x,unsigned char y,unsigned char r,unsigned char Color);
void Lcd_Clear(unsigned char);
void Lcd_WriteStr(unsigned char,unsigned char,unsigned char *);
void Lcd_Reset(void);

unsigned char OSReadKey(void);
unsigned char KeyDown();    //檢測按鍵函數
void Delay10ms(void); //延時10ms

double Random(void);
void InitRandom(unsigned long InitVal);
void InitCpu(void);
void DrawBoardf(void);
void Drawboardt(void);
void PrintScore(void);
void PrintSpeed(void);
void GameOver(void);
void GamePlayo(void);
void GamePlayt(void);
void delay(unsigned int t);
//void Timer0Int(void) interrupt 1 ;

sbit kxuanze=P3^1;
sbit kenter=P3^3;

void delayus(unsigned int j);
void delayms(unsigned int x);
void init(void);
void lcd_wcd(unsigned char com_dat,unsigned char date);
void lcd_st(unsigned char *st);
void scankey(void);
void menu(void);
void jiemian(void);
void moshi(void);
void moshi1(void);
void moshi2(void);
void speed(void);
void Speed1(void);
void Speed2(void);
void Speed3(void);
void Speed4(void);
void game(void);

/*************
測試LCD是否處于忙狀態
如果忙則返回0x80，否則返回0
**************/
unsigned char Lcd_CheckBusy(void)
{
unsigned char Busy;
LcdData=0xff;
RS=0;
RW=1;
E=1;
_nop_();
Busy=LcdData&0x80;
E=0;
return Busy;
}

/*********************************
向LCD寫入字節數據
**********************************/
void Lcd_WriteData(unsigned char Data)
{
while(Lcd_CheckBusy());
RS=1;
RW=0;
E=0;
_nop_();
_nop_();
LcdData=Data;
E=1;
_nop_();
_nop_();
E=0;
}

/***********************************
從LCD中讀出數據
************************************/
unsigned char Lcd_ReadData(void)
{
unsigned char Temp;
while(Lcd_CheckBusy());
LcdData=0xff;
RS=1;
RW=1;
E=1;
_nop_();
   Temp=LcdData;
   E=0;
   return Temp;
}

/*************************************
向LCD中寫入指令代碼
**************************************/
void Lcd_WriteCmd(unsigned char CmdCode)
{
while(Lcd_CheckBusy());
   RS=0;
   RW=0;
   E=0;
   _nop_();
_nop_();
   LcdData=CmdCode;
   _nop_();
_nop_();
   E=1;
   _nop_();
_nop_();
   E=0;
}

void set_postion(unsigned char x,unsigned char y)
{
unsigned char postion;
switch(x)
{
case 0:x=0x80;break;
case 1:x=0x90;break;
case 2:x=0x88;break;
case 3:x=0x98;break;
default:break;
}
postion=x+y;
Lcd_WriteCmd(postion);
}

/*************************************
向LCD指定起始位置寫入一個字符串
*************************************/
void Lcd_WriteStr(unsigned char x,unsigned char y,unsigned char *Str)
{
if((y>3)||(x>7))
return;//如果指定位置不在顯示區域內，則不做任何寫入直接返回
EA=0;
switch(y)
{
case 0:
Lcd_WriteCmd(0x80+x);
break;
case 1:
Lcd_WriteCmd(0x90+x);
break;
case 2:
Lcd_WriteCmd(0x88+x);
break;
case 3:
Lcd_WriteCmd(0x98+x);
break;
}
while(*Str>0)
{
Lcd_WriteData(*Str);
    Str++;
}
EA=1;
}

/**************************************
為加速邏輯運算而設置的掩碼表，這是以犧牲空間而換取時間的辦法
***************************************/
code unsigned int MaskTab[]={0x0001,0x0002,0x0004,0x0008,0x0010,0x0020,0x0040,0x0080,
   0x0100,0x0200,0x0400,0x0800,0x1000,0x2000,0x4000,0x8000};
/***************************************
向LCD指定坐標寫入一個象素,象素顏色有兩種，0代表白（無顯示），1代表黑（有顯示）
****************************************/
void Lcd_PutPixel(unsigned char x,unsigned char y,unsigned char Color)
{
unsigned char z,w;
unsigned int Temp;
if(x>=128||y>=64)
return;
Color=Color%2;
w=15-x%16;//確定對這個字的第多少位進行操作
x=x/16;//確定為一行上的第幾字

if(y<32) //如果為上頁
z=0x80;
else    //否則如果為下頁
z=0x88;

y=y%32;
EA=0;
Lcd_WriteCmd(0x36);
Lcd_WriteCmd(y+0x80);       //行地址
Lcd_WriteCmd(x+z);    //列地址
Temp=Lcd_ReadData();//先空讀一次
Temp=(unsigned int)Lcd_ReadData()<<8;//再讀出高8位
Temp|=(unsigned int)Lcd_ReadData();//再讀出低8位
EA=1;
if(Color==1) //如果寫入顏色為1
Temp|=MaskTab[w];//在此處查表實現加速
else       //如果寫入顏色為0
Temp&=~MaskTab[w];//在此處查表實現加速
EA=0;
Lcd_WriteCmd(y+0x80);       //行地址
Lcd_WriteCmd(x+z);    //列地址
Lcd_WriteData(Temp>>8);//先寫入高8位，再寫入低8位
Lcd_WriteData(Temp&0x00ff);
Lcd_WriteCmd(0x30);
EA=1;
}

/******************************************
從LCD指定坐標讀取象素顏色值
*******************************************/
unsigned char Lcd_ReadPixel(unsigned char x,unsigned char y)
{
unsigned char z,w;
unsigned int Temp;
x=x%128;
y=y%64;
w=15-x%16;//確定對這個字的第多少位進行操作
x=x/16;//確定為一行上的第幾字

if(y<32) //如果為上頁
z=0x80;
else    //否則如果為下頁
z=0x88;

y=y%32;
Lcd_WriteCmd(0x36);
Lcd_WriteCmd(y+0x80);       //行地址
Lcd_WriteCmd(x+z);    //列地址
Temp=Lcd_ReadData();//先空讀一次
Temp=(unsigned int)Lcd_ReadData()<<8;//再讀出高8位
Temp|=(unsigned int)Lcd_ReadData();//再讀出低8位

if((Temp&&MaskTab[w])==0)
return 0;
else
return 1;
}

/***************************************
向LCD指定位置畫一條長度為L(zhǎng)ength的指定顏色的水平線
****************************************/
void Lcd_HoriLine(unsigned char x,unsigned char y,unsigned char Length,unsigned char Color)
{
unsigned char i;
if(Length==0)
return;
for(i=0;i<Length;i++)
{
Lcd_PutPixel(x+i,y,Color);
}
}

/***************************************
向LCD指定位置畫一條長度為L(zhǎng)ength的指定顏色的垂直線
****************************************/
void Lcd_VertLine(unsigned char x,unsigned char y,unsigned char Length,unsigned char Color)
{
unsigned char i;
if(Length==0)
return;
for(i=0;i<Length;i++)
{
Lcd_PutPixel(x,y+i,Color);
}
}

/*******************************************
向LCD指定起始坐標和結束坐標之間畫一條指定顏色的直線
********************************************/
void Lcd_Line(unsigned char x1,unsigned char y1,unsigned char x2,unsigned char y2,unsigned char Color)
{
unsigned int x,y;
unsigned int d_x,d_y;//d_x=x2-x1;d_y=y2-y1;
int err=0;
unsigned char temp=0;
if(y2<y1)
{
x=x1;
y=y1;
x1=x2;
y1=y2;
x2=x;
y2=y;
}
d_y=y2-y1;
if (d_y==0)
{
if (x1>x2)
{
x=x1;
x1=x2;
x2=x;
}
for (x=x1;x<=x2;x++)
Lcd_PutPixel(x,y1,Color);
}

else
{
if(x2>=x1)
{
temp=1;
d_x=x2-x1;
}
else
d_x=x1-x2;
x=x1;
y=y1;
Lcd_PutPixel(x,y,1);

if(temp&&(d_y<=d_x))
while(x!=x2)
{
if(err<0)
{
x=x+1;
err=err+(y2-y);
}
else
{
x=x+1;
y=y+1;
err=err+(y2-y)-(x2-x);
}
Lcd_PutPixel(x,y,Color);
}

else if(temp&&(d_y>d_x))
while(y!=y2)
{
d_x=x2-x;
d_y=y2-y;
if(err<0)
{
x=x+1;
y=y+1;
err=err+d_y-d_x;
}
else
{
y=y+1;
err=err-d_x;
}
Lcd_PutPixel(x,y,Color);

}

else if(!temp&&(d_y<=d_x))
while(x!=x2)
{
d_x=x-x2;
d_y=y2-y;
if(err<0)
{
x=x-1;
err=err+d_y;
}
else
{
x=x-1;
y=y+1;
err=err+d_y-d_x;
}
Lcd_PutPixel(x,y,Color);
}

else if(!temp &&(d_y>d_x))
while(y!=y2)
{
d_x=x-x2;
d_y=y2-y;
if(err<0)
{
x=x-1;
y=y+1;
err=err+d_y-d_x;
}
else
{
y=y+1;
err=err-d_x;
}
Lcd_PutPixel(x,y,Color);
}
}
}

/*******************************************
向LCD指定左上角坐標和右下角坐標畫一個指定顏色的矩形
********************************************/
void Lcd_Rectangle(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char Color)
{
unsigned char Temp;
if(x0>x1)
{
Temp=x0;
x0=x1;
x1=Temp;
}
if(y0>y1)
{
Temp=y0;
y0=y1;
y1=Temp;
}
Lcd_VertLine(x0,y0,y1-y0+1,Color);
Lcd_VertLine(x1,y0,y1-y0+1,Color);
Lcd_HoriLine(x0,y0,x1-x0+1,Color);
Lcd_HoriLine(x0,y1,x1-x0+1,Color);
}

/****************************************
對稱法畫圓的8個鏡像點
*****************************************/
void CircleDot(unsigned char x,unsigned char y,char xx,char yy,unsigned char Color)//內部函數，對稱法畫圓的8個鏡像點
{
Lcd_PutPixel((x+yy),(y+xx),Color);//第 1 個 8 分圓
Lcd_PutPixel((x+xx),(y+yy),Color);//第 2 個 8 分圓
Lcd_PutPixel((x-xx),(y+yy),Color);//第 3 個 8 分圓
Lcd_PutPixel((x-yy),(y+xx),Color);//第 4 個 8 分圓
Lcd_PutPixel((x-yy),(y-xx),Color);//第 5 個 8 分圓
Lcd_PutPixel((x-xx),(y-yy),Color);//第 6 個 8 分圓
Lcd_PutPixel((x+xx),(y-yy),Color);//第 7 個 8 分圓
Lcd_PutPixel((x+yy),(y-xx),Color);//第 8 個 8 分圓
}

/******************************************
向LCD指定圓心坐標畫一個半徑為r的指定顏色的圓
*******************************************/
void Lcd_Circle(unsigned char x,unsigned char y,unsigned char r,unsigned char Color)//中點法畫圓
{//中點法畫圓
unsigned char xx,yy;
char deltax,deltay,d;
xx=0;
yy=r;
deltax=3;
deltay=2-r-r;
d=1-r;
CircleDot(x,y,xx,yy,Color);//對稱法畫圓的8個鏡像點
while (xx<yy)
{
if (d<0)
{
d+=deltax;
deltax+=2;
xx++;
}
else
{
d+=deltax+deltay;
deltax+=2;
deltay+=2;
xx++;
yy--;
}
CircleDot(x,y,xx,yy,Color);//對稱法畫圓的8個鏡像點
}
}

/*****************************************
清除Lcd全屏，如果清除模式Mode為0，則為全屏清除為顏色0（無任何顯示）
否則為全屏清除為顏色1(全屏填充顯示)
******************************************/
void Lcd_Clear(unsigned char Mode)
{
unsigned char x,y,ii;
unsigned char Temp;
if(Mode%2==0)
Temp=0x00;
else
Temp=0xff;
Lcd_WriteCmd(0x36);//擴充指令繪圖顯示
for(ii=0;ii<9;ii+=8)
for(y=0;y<0x20;y++)
for(x=0;x<8;x++)
{
EA=0;
Lcd_WriteCmd(y+0x80);       //行地址
Lcd_WriteCmd(x+0x80+ii);    //列地址
Lcd_WriteData(Temp); //寫數據 D15－D8
Lcd_WriteData(Temp); //寫數據 D7－D0
EA=1;
}
Lcd_WriteCmd(0x30);
}

/****************************************
LCD初始化
*****************************************/
void Lcd_Reset(void)
{
PSB=1;
Lcd_WriteCmd(0x30);    //選擇基本指令集
Lcd_WriteCmd(0x0c);    //開顯示(無游標、不反白)
Lcd_WriteCmd(0x01);    //清除顯示，并且設定地址指針為00H
Lcd_WriteCmd(0x06);    //指定在資料的讀取及寫入時，設定游標的移動方向及指定顯示的移位
}

#define OS_LONG_EYK_EN 1//如果應用中需要處理長按鍵動作，則定義為1，否則定義為0（如果應用中不需要處理長按動作，則建議定義為0，以節省代碼空間）
#define GPIO_KEY P1

unsigned char KeyValue;//用來存放讀取到的鍵值
unsigned char code DIG_CODE[17]={
0,0,0,0,0,5,0,0,6,0,4,0,0,3,0,0,0};

void Delay10ms(void) //誤差 0us
{
unsigned char a,b,c;
for(c=1;c>0;c--)
      for(b=38;b>0;b--)
         for(a=130;a>0;a--);
}
/***********************************************
功能說明：按鍵驅動掃描
入口參數：無
出口參數：掃描一次鍵盤以獲得按鍵句柄
注：交OSReadKey（）函數調用
***********************************************/
unsigned char KeyDown(void)
{
char a=0;
GPIO_KEY=0x0f;
if(GPIO_KEY!=0x0f)//讀取按鍵是否按下
{
Delay10ms();//延時10ms進行消抖
if(GPIO_KEY!=0x0f)//再次檢測鍵盤是否按下
{

//測試列
GPIO_KEY=0X0F;
switch(GPIO_KEY)
{
case(0X07): KeyValue=0;break;
case(0X0b): KeyValue=1;break;
case(0X0d): KeyValue=2;break;
case(0X0e): KeyValue=3;break;
}
//測試行
GPIO_KEY=0XF0;
switch(GPIO_KEY)
{
case(0X70): KeyValue=KeyValue;break;
case(0Xb0): KeyValue=KeyValue+4;break;
case(0Xd0): KeyValue=KeyValue+8;break;
case(0Xe0): KeyValue=KeyValue+12;break;
}
while((a<50)&&(GPIO_KEY!=0xf0))    //檢測按鍵松手檢測
{
Delay10ms();
a++;
}
}
}

return KeyValue;
}
/**********************************************
功能說明：讀取按鍵動作
入口參數：無
出口參數：返回按鍵動作
注意：
沒有按鍵動作，則返回0，
使用矩陣按鍵:向上S12；向下S6;向左S12;向右S9;
***********************************************/
unsigned char OSReadKey(void)
{
static unsigned char KeyEventCnt=0;
static unsigned char KeySampleCnt=0;
static unsigned char KeyBuffer=0;
#define SHORT_ON_DITHERING_COUNTER 3//定義短按按下去抖時間
#define SHORT_OFF_DITHERING_COUNTER 3//定義短按松開去抖時間，一般與短按按下去抖時間相同

#if OS_LONG_KEY_EN>0
static unsigned int LongKeySampleCnt=0;
#define LONG_ON_DITHERING_COUNTER 250//定義長按按下確認需要的時間，如果是每1MS調用一次OSReadKey()，則1000意味著這個時間為1S
#define LONG_OFF_DITHERING_COUNTER 3//定義長按松開去抖時間，一般和短按去抖時間相同
#endif
unsigned char KeyTemp;
KeyTemp=DIG_CODE[KeyDown()];
switch(KeyEventCnt)
{
case 0:
if(KeyTemp!=0)
{
KeySampleCnt=0;
KeyBuffer=KeyTemp;
KeyEventCnt=1;
}
return 0;//no key on,return 0
break;

#if OS_LONG_KEY_EN>0
case 1:
if(KeyTemp!=KeyBuffer)
{
KeyEventCnt=0;
return 0;//is dithering,return 0
}
else
{
if(++KeySampleCnt>SHORT_ON_DITHERING_COUNTER)
{
KeySampleCnt=0;
KeyEventCnt=2;
LongKeySampleCnt=0;
return ((KeyBuffer-1)<<2)+1;//sure that key on,return (KeyBuffer-1)<<2+1
}
else
return 0;//not sure that key on,return 0
}
break;

case 2:
if(++LongKeySampleCnt>LONG_ON_DITHERING_COUNTER)
{
KeySampleCnt=0;
KeyEventCnt=3;
return ((KeyBuffer-1)<<2)+2; //sure that key long on,return (KeyBuffer-1)<<2+2
}
else
{
if(KeyTemp!=KeyBuffer)
{
if(++KeySampleCnt>SHORT_OFF_DITHERING_COUNTER)
{
KeyEventCnt=0;
return ((KeyBuffer-1)<<2)+3;//after short on to off,(KeyBuffer-1)<<2+3
}
else
return 0;
}
else
{
KeySampleCnt=0;
return 0;
}
}
break;

case 3:
if(KeyTemp!=KeyBuffer)
{
if(++KeySampleCnt>LONG_OFF_DITHERING_COUNTER)
{
KeyEventCnt=0;
return ((KeyBuffer-1)<<2)+4;  //after long key on turn to off,(KeyBuffer-1)<<2+4
}
else
return 0;
}
else
{
KeySampleCnt=0;
return 0;
}
break;

#else
case 1:
if(KeyTemp!=KeyBuffer)
{
KeyEventCnt=0;
return 0;//is dithering,return 0
}
else
{
if(++KeySampleCnt>=SHORT_ON_DITHERING_COUNTER)
{
KeySampleCnt=0;
KeyEventCnt=2;
return ((KeyBuffer-1)<<2)+1;//sure that key on,return (KeyBuffer-1)<<2+1
}
else
return 0;//not sure that key on,return 0
}
break;

case 2:
if(KeyTemp!=KeyBuffer)
{
if(++KeySampleCnt>=SHORT_OFF_DITHERING_COUNTER)
{
KeyEventCnt=0;
return ((KeyBuffer-1)<<2)+3;//after short on to off,(KeyBuffer-1)<<2+3
}
else
return 0;
}
else
{
KeySampleCnt=0;
return 0;
}
break;
#endif

default:break;
}
return 0;
}

#define uchar unsigned char
#define uint unsigned int

static unsigned long Seed = 1;
#define A 48271L
#define M 2147483647L
#define Q (M / A)
#define R (M % A)

void delay(unsigned int t)
{
unsigned int i,j;
for(i=0;i<t;i++)
for(j=0;j<10;j++);
}

/************************************
偽隨機數發生器
*************************************/
double Random(void)
{
long TmpSeed;
TmpSeed=A*(Seed%Q)-R*(Seed/Q);
if(TmpSeed>=0)
Seed=TmpSeed;
else
Seed=TmpSeed+M;
return (double)Seed/M;
}

/**************************************
為偽隨機數發生器播種
***************************************/
void InitRandom(unsigned long InitVal)
{
Seed=InitVal;
}

/*********************************
初始化MPU
**********************************/
void InitCpu(void)
{
TMOD=0x01;
TH0=0;
TL0=0;
TR0=1;
ET0=1;
EA=1;
}

#define N 25
struct Food
{
unsigned char x;
unsigned char y;
unsigned char yes;
}food;//食物結構體
struct Snake
{
unsigned char x[N];
unsigned char y[N];
unsigned char node;
unsigned char direction;
unsigned char life;
}snake;//蛇結構體

unsigned char Flag=0;
unsigned char Score=0;
unsigned char Speed;    //speed越大，速度越慢
unsigned char KeyBuffer=0;
#define FUNC 1    //(P3^1)表示級別
#define UP 2    //(P3^3)表示左
#define DOWN 3    //(P3^5)表示右
#define LEFT 4    //(P3^4)表示下
#define RIGHT 5    //(P3^2)表示上
#define PASSSCORE 20    //預定義過關成績
void Timer0Int(void) interrupt 1
{
switch(OSReadKey())
{
case 5:
KeyBuffer=FUNC;    //表示級別
/*if(++Speed>=10)
Speed=1;
   Flag|=1<<1;//速度變化標志置1*/
break;
case 21:
KeyBuffer=DOWN;    //表示右
/*if(snake.direction!=2)
snake.direction=1;*/
break;
case 13:
KeyBuffer=UP;    //表示左
/*if(snake.direction!=1)
snake.direction=2;*/
break;
case 9:
KeyBuffer=RIGHT;    //表示上
/*if(snake.direction!=4)
snake.direction=3;*/
break;
   case 17:
KeyBuffer=LEFT;    //表示下
/*if(snake.direction!=3)
snake.direction=4;*/
break;
default:
break;
}
}

/******************************
畫墻壁，初始化界面
*******************************/
void DrawBoardf(void)
{
unsigned char n;
for(n=0;n<31;n++)
{
Lcd_Rectangle(3*n,0,3*n+2,2,1);
Lcd_Rectangle(3*n,60,3*n+2,62,1);
}
for(n=0;n<21;n++)
{
Lcd_Rectangle(0,3*n,2,3*n+2,1);
Lcd_Rectangle(90,3*n,92,3*n+2,1);
}
Lcd_HoriLine(93,31,35,1);
Lcd_HoriLine(93,63,35,1);
}

void Drawboardt(void)
{
unsigned char n;
for(n=0;n<21;n++)
{
Lcd_Rectangle(0,3*n,2,3*n+2,1);
Lcd_Rectangle(90,3*n,92,3*n+2,1);
}
Lcd_HoriLine(93,31,35,1);
Lcd_HoriLine(93,63,35,1);
}

/***************************
打印成績
****************************/
void PrintScore(void)
{
unsigned char Str[3];
Lcd_WriteStr(6,0,"成績");
Str[0]=(Score/10)|0x30;//十位
Str[1]=(Score%10)|0x30;//個位
Str[2]=0;
Lcd_WriteStr(7,1,Str);
}

/********************************
打印速度級別
*********************************/
void PrintSpeed(void)
{
unsigned char Str[2];
Lcd_WriteStr(6,2,"級別");
Str[0]=Speed|0x30;
Str[1]=0;
Lcd_WriteStr(7,3,Str);
}

/***********************************
游戲結束處理
************************************/
void GameOver(void)
{
unsigned char n;
Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,0);//消隱出食物
for(n=1;n<snake.node;n++)
{
Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,0);//消隱食物，蛇頭已到墻壁內，故不用消去
}
if(snake.life==0)//如果蛇還活著
Lcd_WriteStr(2,1,"過關");
else          //如果蛇死了
Lcd_WriteStr(2,1,"輸了");
Lcd_WriteStr(1,2,"游戲結束");
}

/********************************
游戲的具體過程，也是貪吃蛇算法的關鍵部分
*********************************/
void GamePlayo(void)
{
unsigned char n;
InitRandom(TL0);
food.yes=1;//1表示需要出現新事物，0表示已經存在食物尚未吃掉
snake.life=0;//表示蛇還活著
snake.direction=DOWN;
snake.x[0]=6;snake.y[0]=6;
snake.x[1]=3;snake.y[1]=6;
snake.node=2;
PrintScore();
PrintSpeed();
while(1)
{
if(food.yes==1)
{
while(1)
{
food.x=Random()*85+3;
food.y=Random()*55+3;//獲得隨機數

while(food.x%3!=0)
food.x++;
while(food.y%3!=0)
food.y++;
      for(n=0;n<snake.node;n++)//判斷產生的食物坐標是否和蛇身重合
{
if((food.x==snake.x[n])&&(food.y==snake.y[n]))
break;
}
if(n==snake.node)
{
food.yes=0;
break;//產生有效的食物坐標
}
}
}
if(food.yes==0)
{
Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,1);
}
for(n=snake.node-1;n>0;n--)
{
snake.x[n]=snake.x[n-1];
snake.y[n]=snake.y[n-1];
}
switch(snake.direction)
{
case DOWN:snake.x[0]+=3;break;
case UP:snake.x[0]-=3;break;
case RIGHT:snake.y[0]-=3;break;
case LEFT:snake.y[0]+=3;break;
default:break;
}
for(n=3;n<snake.node;n++)//從第三節開始判斷蛇頭是否咬到自己
{
if(snake.x[n]==snake.x[0]&&snake.y[n]==snake.y[0])
{
GameOver();
snake.life=1;
break;
}
}
if(snake.x[0]<3||snake.x[0]>=90||snake.y[0]<3||snake.y[0]>=60)//判蛇頭是否撞到墻壁
{
GameOver();
snake.life=1;
}
if(snake.life==1)
break;//蛇死，則跳出while(1)循環
if(snake.x[0]==food.x&&snake.y[0]==food.y)//判蛇是否吃到食物
{
Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,0);//消隱食物
snake.x[snake.node]=200;
snake.y[snake.node]=200;//產生蛇新的節坐標先放在看不見的位置
snake.node++;//蛇節數加1
food.yes=1;//食物標志置1
if(++Score>=PASSSCORE)
{
PrintScore();
GameOver();
break;
}
PrintScore();
}
for(n=0;n<snake.node;n++)
{
Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
}//根據蛇的節數畫出蛇
delay(Speed*1000);    //調速
delay(Speed*1000);
Lcd_Rectangle(snake.x[snake.node-1],snake.y[snake.node-1],snake.x[snake.node-1]+2,snake.y[snake.node-1]+2,0);
switch(KeyBuffer)
{
case FUNC:
KeyBuffer=0;
if(++Speed>=10)
Speed=1;
   PrintSpeed();
break;
case DOWN:
KeyBuffer=0;
if(snake.direction!=UP)
snake.direction=DOWN;
break;
case UP:
KeyBuffer=0;
if(snake.direction!=DOWN)
snake.direction=UP;
break;
case RIGHT:
KeyBuffer=0;
if(snake.direction!=LEFT)
snake.direction=RIGHT;
break;
   case LEFT:
KeyBuffer=0;
if(snake.direction!=RIGHT)
snake.direction=LEFT;
break;
default:
break;
}
}//結束while(1)
}

void GamePlayt(void)
{
unsigned char n;
InitRandom(TL0);
food.yes=1;//1表示需要出現新事物，0表示已經存在食物尚未吃掉
snake.life=0;//表示蛇還活著
snake.direction=DOWN;
snake.x[0]=6;snake.y[0]=6;
snake.x[1]=3;snake.y[1]=6;
snake.node=2;
PrintScore();
PrintSpeed();
while(1)
{
if(food.yes==1)
{
while(1)
{
food.x=Random()*85+3;
food.y=Random()*55+3;//獲得隨機數

while(food.x%3!=0)
food.x++;
while(food.y%3!=0)
food.y++;
      for(n=0;n<snake.node;n++)//判斷產生的食物坐標是否和蛇身重合
{
if((food.x==snake.x[n])&&(food.y==snake.y[n]))
break;
}
if(n==snake.node)
{
food.yes=0;
break;//產生有效的食物坐標
}
}
}
if(food.yes==0)
{
Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,1);
}
for(n=snake.node-1;n>0;n--)
{
snake.x[n]=snake.x[n-1];
snake.y[n]=snake.y[n-1];
}
switch(snake.direction)
{
case DOWN:snake.x[0]+=3;break;
case UP:snake.x[0]-=3;break;
case RIGHT:snake.y[0]-=3;break;
case LEFT:snake.y[0]+=3;break;
default:break;
}
for(n=3;n<snake.node;n++)//從第三節開始判斷蛇頭是否咬到自己
{
if(snake.x[n]==snake.x[0]&&snake.y[n]==snake.y[0])
{
GameOver();
snake.life=1;
break;
}
}

if(snake.x[0]<3||snake.x[0]>=90)//判蛇頭是否撞到墻壁
{
GameOver();
snake.life=1;
}
if(snake.life==1)
break;//蛇死，則跳出while(1)循環

if(snake.y[0]<3||snake.y[0]>=60)
{  if(snake.y[0]<3)
   snake.y[0]=59;
//       for(n=0;n<snake.node;n++)
// {
// Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
// }//根據蛇的節數畫出蛇
   if(snake.y[0]>=60)
   snake.y[0]=3;
//    for(n=0;n<snake.node;n++)
// {
// Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
// }//根據蛇的節數畫出蛇
//

}
if(snake.x[0]==food.x&&snake.y[0]==food.y)//判蛇是否吃到食物
{
Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,0);//消隱食物
snake.x[snake.node]=200;
snake.y[snake.node]=200;//產生蛇新的節坐標先放在看不見的位置
snake.node++;//蛇節數加1
food.yes=1;//食物標志置1
if(++Score>=PASSSCORE)
{
PrintScore();
GameOver();
break;
}
PrintScore();
}
for(n=0;n<snake.node;n++)
{
Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
}//根據蛇的節數畫出蛇
delay(Speed*1000);    //調速
delay(Speed*1000);
Lcd_Rectangle(snake.x[snake.node-1],snake.y[snake.node-1],snake.x[snake.node-1]+2,snake.y[snake.node-1]+2,0);
switch(KeyBuffer)
{
case FUNC:
KeyBuffer=0;
if(++Speed>=10)
Speed=1;
   PrintSpeed();
break;
case DOWN:
KeyBuffer=0;
if(snake.direction!=UP)
snake.direction=DOWN;
break;
case UP:
KeyBuffer=0;
if(snake.direction!=DOWN)
snake.direction=UP;
break;
case RIGHT:
KeyBuffer=0;
if(snake.direction!=LEFT)
snake.direction=RIGHT;
break;
   case LEFT:
KeyBuffer=0;
if(snake.direction!=RIGHT)
snake.direction=LEFT;
break;
default:
break;
}
}//結束while(1)
}

unsigned char flag,flag1,s1num;

void delayus(unsigned int j)
{
unsigned char i;
for(i=j;i>0;i--);
}

void delayms(unsigned int x)
{
unsigned char i,j;
for(i=x;i>0;i--)
for(j=110;j>0;j--);
}

void init(void)
{
PSB=1;
Lcd_WriteCmd(0x01);
delayms(5);
Lcd_WriteCmd(0x30);
delayms(5);
Lcd_WriteCmd(0x0c);
delayms(5);
}

void scankey(void)
{
if(kxuanze==0)  //選擇鍵
{
delayms(10);
if(kxuanze==0)    //如果S1確定按下
{s1num++;    //變量加一
while(!kxuanze);    //等待按鍵松開
if(s1num==1)    //等待按鍵松開
{
set_postion(0,4);    //一行三列（第一菜單的界面）
Lcd_WriteCmd(0x0f); //光標閃爍
}
}
if(s1num==2)    //變量為2
{
set_postion(1,2);    //二行三列
Lcd_WriteCmd(0x0f);    //光標閃爍
}
if(s1num==3)    //變量為3
{
set_postion(2,2);
Lcd_WriteCmd(0x0f);
}
if(s1num==4)
{
s1num=0;
}
}
if(s1num!=0) //如果slnum不等于0，目的是為了讓S1鍵起作用后S2鍵才發揮相應的作用
{
if(kenter==0)    //如果S2按下（確定鍵）
{
delayms(10); //延時消抖
if(kenter==0)    //如果S2（確定鍵）確實按下
{
++flag;    //flag自加1，設置變量的目的是為了方便設置子菜單中的下一級菜單
while(!kenter);    //等待按鍵松開
if((s1num==1)&&(flag==1)) //與選擇鍵中選中的相應欄目對應
{
flag1=1;
s1num=0;
Lcd_WriteCmd(0x01);    //清屏
delayms(5);
Lcd_WriteCmd(0x0f);
delayms(5);    //目的為了當進入父菜單后的子菜單，S1鍵能發揮作用
game ();
}
}
if((s1num==2)&&(flag==1))
{ flag1=1;
s1num=0;
Lcd_WriteCmd(0x01);    //清屏
delayms(5);
Lcd_WriteCmd(0x0f);
delayms(5);
speed();    //目的為了當進入父菜單后的子菜單，S1鍵能發揮作用
}
if((s1num==1)&&(flag==2))  //如果變量為2.，進入子菜單的下一級菜單，下s1num==1，否則會進入誤操作
{
Lcd_WriteCmd(0x0C);
delayms(5);
Lcd_WriteCmd(0x01);
delayms(5);
Speed1();
}
if((s1num==2)&&(flag==2))  //if((s1num==2)&&(flag==2)&&(flag==1))
{
Lcd_WriteCmd(0x0C);
delayms(5);
Lcd_WriteCmd(0x01);
delayms(5);
Speed2();
}
if((s1num==3)&&(flag==2))
{
Lcd_WriteCmd(0x0C);
delayms(5);
Lcd_WriteCmd(0x01);
delayms(5);
Speed3();
}
if((s1num==4)&&(flag==2))
{
Lcd_WriteCmd(0x0C);
delayms(5);
Lcd_WriteCmd(0x01);
delayms(5);
Speed4();
}
if((s1num==3)&&(flag==1))
{
flag1=1;
s1num=0;    //目的為了當進入父菜單后的子菜單，S1鍵能發揮作用
Lcd_WriteCmd(0x01);    //清屏
delayms(5);
Lcd_WriteCmd(0x0f);
delayms(5);
moshi();
}
if((s1num==1)&&(flag==2))
{
Lcd_WriteCmd(0x0C);
delayms(5);
Lcd_WriteCmd(0x01);
delayms(5);
moshi1();
}
if((s1num==2)&&(flag==2))
{
Lcd_WriteCmd(0x0C);
delayms(5);
Lcd_WriteCmd(0x01);
delayms(5);
moshi2();
}
if(s1num==4)
{
s1num=0;
}
if(flag==3)
{
flag=0;
}
}
}

}

void jiemian(void)
{
Lcd_WriteStr(0,1,"Welcome to");
Lcd_WriteStr(2,2,"貪吃蛇");

delayms(20000);
Lcd_WriteCmd(0x01);
}

void menu(void)
{
Lcd_WriteStr(0,1,"開始游戲");
Lcd_WriteStr(1,1,"速度選擇");
Lcd_WriteStr(2,1,"模式設置");

}

void speed(void)
{
Lcd_WriteStr(0,1,"Speed1");

Lcd_WriteStr(1,1,"Speed2");

Lcd_WriteStr(2,1,"Speed3");

Lcd_WriteStr(3,1,"Speed4");

}

void moshi(void)
{
Lcd_WriteStr(0,1,"mosho1");

Lcd_WriteStr(1,1,"moshi2");

}

void moshi1(void)
{
unsigned char moshi;
moshi=1;
void Drawboardo();
void GamePlayf();
}

void moshi2(void)
{
unsigned char moshi;
moshi=2;
void Drawboardt();
void GamePlayt();
}

void Speed1(void)
{
unsigned char Speed=1;
}

void Speed2(void)
{
unsigned char Speed=2;
}

void Speed3(void)
{
unsigned char Speed=3;

}

void Speed4(void)
{
unsigned char Speed=4;
}

void game(void)
{

InitCpu();//初始化CPU
Lcd_Reset(); //初始化LCD屏
//Lcd_WriteStr(2,1,"Welcome");
delay(5000);
Lcd_WriteCmd(0x01); //清除顯示，并且設定地址指針為00H
Lcd_Clear(0);//清屏
switch(Speed)
{
   case '1':
   Speed1();
   break;
   case '2':
   Speed2();
   break;
   case '3':
   Speed3();
   break;
   case '4':
   Speed4();
   break;
   default:
   Speed4();

}
switch(moshi)
{
   case '1':
   moshi1();
   break;
   case '2':
   moshi2;
   break;
   default:
   moshi2();
}
GameOver();//游戲結束

}

IMG_20180813_195553.jpg (123.35 KB, 下載次數: 24)

題目要求

1534161529241.jpg (2.61 MB, 下載次數: 23)

tanchishe.zip

59.33 KB, 下載次數: 8

多c多h版

tanchishe.zip

30.28 KB, 下載次數: 6

一個函數版

作者: angmall 時間: 2018-8-13 23:34
少了這個

#define OS_LONG_EYK_EN 1 //如果應用中需要處理長按鍵動作，則定義為1，否則定義為0（如果應用中不需要處理長按動作，則建議定義為0，以節省代碼空間）
#define GPIO_KEY P1

作者: lynn710 時間: 2018-8-14 15:16

angmall 發表于 2018-8-13 23:34
少了這個

#define OS_LONG_EYK_EN 1 //如果應用中需要處理長按鍵動作，則定義為1，否則定義為0（如果應 ...

我加了還是那個錯

作者: angmall 時間: 2018-8-14 18:15
這個試試

#define OS_LONG_KEY_EN 1

作者: lynn710 時間: 2018-8-15 02:09

angmall 發表于 2018-8-14 18:15
這個試試

#define OS_LONG_KEY_EN 1

大神，沒有錯了，但是單片機運行好像卡住了，我一直按復位鍵前面的部分功能才可能好用，后面的一直用不了，但我各功能分開檢測得時候是都好用得

作者: lynn710 時間: 2018-8-15 02:35
#include"reg52.h"
#include "intrins.h"
sbit RS=P2^6; //并行的指令/數據選擇信號, H數據, L命令
sbit RW=P2^5; //并行讀寫選擇信號, H讀, L寫
sbit E=P2^7; //并行使能端, H有效, L無效
sbit PSB=P3^2; //并/串接口選擇, H并,L串
sbit RET=P3^4; //復位, L有效
sbit kxuanze=P3^1;
sbit kenter=P3^3;
#define  LcdData P0
#define N 25
unsigned char moshiceshi;
unsigned char flag,s1num;
#define OS_LONG_EYK_EN 1       //如果應用中需要處理長按鍵動作，則定義為1，否則定義為0（如果應用中不需要處理長按動作，則建議定義為0，以節省代碼空間）
#define GPIO_KEY P1
unsigned char KeyValue;//用來存放讀取到的鍵值
unsigned char code DIG_CODE[17]={
0,0,0,0,0,5,0,0,6,0,4,0,0,3,0,0,0};
#define uchar unsigned char
#define uint unsigned int
static unsigned long Seed = 1;
#define A 48271L
#define M 2147483647L
#define Q (M / A)
#define R (M % A)
struct Food
{
unsigned char x;
unsigned char y;
unsigned char yes;
}food;//食物結構體
struct Snake
{
unsigned char x[N];
unsigned char y[N];
unsigned char node;
unsigned char direction;
unsigned char life;
}snake;//蛇結構體
unsigned char Flag_gamedisplay=0;
unsigned char Score=0;
unsigned char Speed_tiaosu;    //speed越大，速度越慢
unsigned char KeyBuffer=0;
#define FUNC 1    //(P3^1)表示級別
#define UP 2    //(P3^3)表示左
#define DOWN 3    //(P3^5)表示右
#define LEFT 4    //(P3^4)表示下
#define RIGHT 5    //(P3^2)表示上
#define PASSSCORE 20    //預定義過關成績

void Lcd_WriteData(unsigned char);
unsigned char Check_Busy(void);
unsigned char Lcd_ReadData(void);
void Lcd_WriteCmd(unsigned char);
void Lcd_PutPixel(unsigned char,unsigned char,unsigned char);
//unsigned char Lcd_ReadPixel(unsigned char,unsigned char);
void Lcd_HoriLine(unsigned char,unsigned char,unsigned char Length,unsigned char Color);
void Lcd_VertLine(unsigned char x,unsigned char y,unsigned char Length,unsigned char Color);
void Lcd_Line(unsigned char x1,unsigned char y1,unsigned char x2,unsigned char y2,unsigned char Color);
void Lcd_Rectangle(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char Color);
void Lcd_Circle(unsigned char x,unsigned char y,unsigned char r,unsigned char Color);
void Lcd_Clear(unsigned char);
void Lcd_WriteStr(unsigned char,unsigned char,unsigned char *);
void Lcd_Reset(void);
unsigned char OSReadKey(void);
unsigned char KeyDown(); //檢測按鍵函數
void Delay10ms(void); //延時10ms
double Random(void);
void InitRandom(unsigned long InitVal);
void InitCpu(void);
void DrawBoardf();
void Drawboardt(void);
void PrintScore(void);
void PrintSpeed(void);
void GameOver(void);
void Gameplayt(void);
void GamePlayf(void);
void delay(unsigned int t);
void delayus(unsigned int j);
void lcd_st(unsigned char *st);
void scankey(void);
void moshi(void);
void zhujiemian(void);
unsigned char moshi1(void);
unsigned char moshi2(void);
void speed(void);
void Speed1(void);
void Speed2(void);
void Speed3(void);
void Speed4(void);
void game(void);

void main()
{
Lcd_Reset();
Lcd_WriteStr(0,0,"Welcome");
Lcd_WriteStr(2,2,"貪吃蛇");
delay(20000000);
zhujiemian();
while(1)
{
  scankey();
}
}

/*************
測試LCD是否處于忙狀態
如果忙則返回0x80，否則返回0
**************/
unsigned char Lcd_CheckBusy(void)
{
unsigned char Busy;
LcdData=0xff;
RS=0;
RW=1;
E=1;
_nop_();
Busy=LcdData&0x80;
E=0;
return Busy;
}
/*********************************
向LCD寫入字節數據
**********************************/
void Lcd_WriteData(unsigned char LCD_Data)
{
while(Lcd_CheckBusy());
RS=1;
RW=0;
E=0;
_nop_();
_nop_();
LcdData=LCD_Data;
E=1;
_nop_();
_nop_();
E=0;
}
/***********************************
從LCD中讀出數據
************************************/
unsigned char Lcd_ReadData(void)
{
unsigned char Temp;
//while(Lcd_CheckBusy());
  LcdData=0xff;
  RS=1;
RW=1;
E=1;
_nop_();
Temp=LcdData;
E=0;
return Temp;
}
/*************************************
向LCD中寫入指令代碼
**************************************/
void Lcd_WriteCmd(unsigned char CmdCode)
{
while(Lcd_CheckBusy());
RS=0;
RW=0;
E=0;
_nop_();
_nop_();
LcdData=CmdCode;
_nop_();
_nop_();
E=1;
_nop_();
_nop_();
E=0;
}
void set_postion(unsigned char x,unsigned char y)
{
unsigned char postion;
switch(x)
{
case 0:x=0x80;break;
case 1:x=0x90;break;
case 2:x=0x88;break;
case 3:x=0x98;break;
default:break;
}
postion=x+y;
Lcd_WriteCmd(postion);
}
/*************************************
向LCD指定起始位置寫入一個字符串
*************************************/
void Lcd_WriteStr(unsigned char x,unsigned char y,unsigned char *Str)
{
if((y>3)||(x>7))
  return;//如果指定位置不在顯示區域內，則不做任何寫入直接返回
EA=0;
switch(y)
{
  case 0:
Lcd_WriteCmd(0x80+x);
break;
  case 1:
Lcd_WriteCmd(0x90+x);
break;
  case 2:
Lcd_WriteCmd(0x88+x);
break;
  case 3:
Lcd_WriteCmd(0x98+x);
break;
}
while(*Str>0)
{
  Lcd_WriteData(*Str);
Str++;
}
EA=1;
}
/**************************************
為加速邏輯運算而設置的掩碼表，這是以犧牲空間而換取時間的辦法
***************************************/
code unsigned int MaskTab[]={0x0001,0x0002,0x0004,0x0008,0x0010,0x0020,0x0040,0x0080,
      0x0100,0x0200,0x0400,0x0800,0x1000,0x2000,0x4000,0x8000};
/***************************************
向LCD指定坐標寫入一個象素,象素顏色有兩種，0代表白（無顯示），1代表黑（有顯示）
****************************************/
void Lcd_PutPixel(unsigned char x,unsigned char y,unsigned char Color)
{
unsigned char z,w;
unsigned int Temp;
if(x>=128||y>=64)
  return;
Color=Color%2;
w=15-x%16;//確定對這個字的第多少位進行操作
x=x/16;//確定為一行上的第幾字
if(y<32) //如果為上頁
  z=0x80;
else    //否則如果為下頁
  z=0x88;
y=y%32;
EA=0;
Lcd_WriteCmd(0x36);
Lcd_WriteCmd(y+0x80);       //行地址
Lcd_WriteCmd(x+z);    //列地址
Temp=Lcd_ReadData();//先空讀一次
Temp=(unsigned int)Lcd_ReadData()<<8;//再讀出高8位
Temp|=(unsigned int)Lcd_ReadData();//再讀出低8位
EA=1;
if(Color==1) //如果寫入顏色為1
  Temp|=MaskTab[w];//在此處查表實現加速
else       //如果寫入顏色為0
  Temp&=~MaskTab[w];//在此處查表實現加速
EA=0;
Lcd_WriteCmd(y+0x80);       //行地址
Lcd_WriteCmd(x+z);    //列地址
Lcd_WriteData(Temp>>8);//先寫入高8位，再寫入低8位
Lcd_WriteData(Temp&0x00ff);
Lcd_WriteCmd(0x30);
EA=1;
}
/***************************************
向LCD指定位置畫一條長度為L(zhǎng)ength的指定顏色的水平線
****************************************/
void Lcd_HoriLine(unsigned char x,unsigned char y,unsigned char Length,unsigned char Color)
{
unsigned char i;
if(Length==0)
  return;
for(i=0;i<Length;i++)
{
  Lcd_PutPixel(x+i,y,Color);
}
}
/***************************************
向LCD指定位置畫一條長度為L(zhǎng)ength的指定顏色的垂直線
****************************************/
void Lcd_VertLine(unsigned char x,unsigned char y,unsigned char Length,unsigned char Color)
{
unsigned char i;
if(Length==0)
  return;
for(i=0;i<Length;i++)
{
  Lcd_PutPixel(x,y+i,Color);
}
}
/*******************************************
向LCD指定起始坐標和結束坐標之間畫一條指定顏色的直線
void Lcd_Line(unsigned char x1,unsigned char y1,unsigned char x2,unsigned char y2,unsigned char Color)
{
unsigned int x,y;
unsigned int d_x,d_y;//d_x=x2-x1;d_y=y2-y1;
int err=0;
unsigned char temp=0;
if(y2<y1)
{
  x=x1;
  y=y1;
  x1=x2;
  y1=y2;
  x2=x;
  y2=y;
}
d_y=y2-y1;
if (d_y==0)
{
  if (x1>x2)
  {
x=x1;
x1=x2;
x2=x;
  }
  for (x=x1;x<=x2;x++)
Lcd_PutPixel(x,y1,Color);
}
else
{
  if(x2>=x1)
  {
temp=1;
d_x=x2-x1;
  }
  else
d_x=x1-x2;
  x=x1;
  y=y1;
  Lcd_PutPixel(x,y,1);
  if(temp&&(d_y<=d_x))
while(x!=x2)
{
if(err<0)
{
   x=x+1;
   err=err+(y2-y);
}
else
{
   x=x+1;
   y=y+1;
   err=err+(y2-y)-(x2-x);
}
Lcd_PutPixel(x,y,Color);
}
  else if(temp&&(d_y>d_x))
while(y!=y2)
{
d_x=x2-x;
d_y=y2-y;
if(err<0)
{
   x=x+1;
   y=y+1;
   err=err+d_y-d_x;
}
else
{
   y=y+1;
   err=err-d_x;
}
Lcd_PutPixel(x,y,Color);
}
  else if(!temp&&(d_y<=d_x))
while(x!=x2)
{
d_x=x-x2;
d_y=y2-y;
if(err<0)
{
   x=x-1;
   err=err+d_y;
}
else
{
   x=x-1;
   y=y+1;
   err=err+d_y-d_x;
}
Lcd_PutPixel(x,y,Color);
}
  else if(!temp &&(d_y>d_x))
while(y!=y2)
{
d_x=x-x2;
d_y=y2-y;
if(err<0)
{
   x=x-1;
   y=y+1;
   err=err+d_y-d_x;
}
else
{
   y=y+1;
   err=err-d_x;
}
Lcd_PutPixel(x,y,Color);
}
}
}
********************************************/
/*******************************************
向LCD指定左上角坐標和右下角坐標畫一個指定顏色的矩形
********************************************/
void Lcd_Rectangle(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char Color)
{
unsigned char Temp;
if(x0>x1)
{
  Temp=x0;
  x0=x1;
  x1=Temp;
}
if(y0>y1)
{
  Temp=y0;
  y0=y1;
  y1=Temp;
}
Lcd_VertLine(x0,y0,y1-y0+1,Color);
Lcd_VertLine(x1,y0,y1-y0+1,Color);
Lcd_HoriLine(x0,y0,x1-x0+1,Color);
Lcd_HoriLine(x0,y1,x1-x0+1,Color);
}
/****************************************
對稱法畫圓的8個鏡像點
void CircleDot(unsigned char x,unsigned char y,char xx,char yy,unsigned char Color)//內部函數，對稱法畫圓的8個鏡像點
{
Lcd_PutPixel((x+yy),(y+xx),Color);//第 1 個 8 分圓
Lcd_PutPixel((x+xx),(y+yy),Color);//第 2 個 8 分圓
Lcd_PutPixel((x-xx),(y+yy),Color);//第 3 個 8 分圓
Lcd_PutPixel((x-yy),(y+xx),Color);//第 4 個 8 分圓
Lcd_PutPixel((x-yy),(y-xx),Color);//第 5 個 8 分圓
Lcd_PutPixel((x-xx),(y-yy),Color);//第 6 個 8 分圓
Lcd_PutPixel((x+xx),(y-yy),Color);//第 7 個 8 分圓
Lcd_PutPixel((x+yy),(y-xx),Color);//第 8 個 8 分圓
}
*****************************************/
/******************************************
向LCD指定圓心坐標畫一個半徑為r的指定顏色的圓
void Lcd_Circle(unsigned char x,unsigned char y,unsigned char r,unsigned char Color)//中點法畫圓
{//中點法畫圓
unsigned char xx,yy;
char deltax,deltay,d;
xx=0;
yy=r;
deltax=3;
deltay=2-r-r;
d=1-r;
CircleDot(x,y,xx,yy,Color);//對稱法畫圓的8個鏡像點
while (xx<yy)
{
  if (d<0)
  {
d+=deltax;
deltax+=2;
xx++;
  }
  else
  {
d+=deltax+deltay;
deltax+=2;
deltay+=2;
xx++;
yy--;
  }
  CircleDot(x,y,xx,yy,Color);//對稱法畫圓的8個鏡像點
}
}
*******************************************/
/*****************************************
清除Lcd全屏，如果清除模式Mode為0，則為全屏清除為顏色0（無任何顯示）
否則為全屏清除為顏色1(全屏填充顯示)
******************************************/
void Lcd_Clear(unsigned char Mode)
{
unsigned char x,y,ii;
unsigned char Temp;
if(Mode%2==0)
  Temp=0x00;
else
  Temp=0xff;
Lcd_WriteCmd(0x36);//擴充指令繪圖顯示
for(ii=0;ii<9;ii+=8)
  for(y=0;y<0x20;y++)
for(x=0;x<8;x++)
{
EA=0;
Lcd_WriteCmd(y+0x80);       //行地址
Lcd_WriteCmd(x+0x80+ii);    //列地址
Lcd_WriteData(Temp); //寫數據 D15－D8
Lcd_WriteData(Temp); //寫數據 D7－D0
EA=1;
}
Lcd_WriteCmd(0x30);
}
/****************************************
LCD初始化
*****************************************/
void Lcd_Reset(void)
{
PSB=1;
Lcd_WriteCmd(0x30);    //選擇基本指令集
delay(5);
Lcd_WriteCmd(0x0c);    //開顯示(無游標、不反白)
delay(5);
Lcd_WriteCmd(0x01);    //清除顯示，并且設定地址指針為00H
delay(5);
Lcd_WriteCmd(0x06);    //指定在資料的讀取及寫入時，設定游標的移動方向及指定顯示的移位
}

void Delay10ms(void) //誤差 0us
{
unsigned char a,b,c;
for(c=1;c>0;c--)
      for(b=38;b>0;b--)
         for(a=130;a>0;a--);
}
void delay(unsigned int t)
{
unsigned int i,j;
for(i=0;i<t;i++)
for(j=0;j<10;j++);
}
/***********************************************
按鍵驅動掃描
掃描一次鍵盤以獲得按鍵句柄
注：交OSReadKey（）函數調用
***********************************************/
unsigned char KeyDown(void)
{
char a=0;
GPIO_KEY=0x0f;
if(GPIO_KEY!=0x0f)//讀取按鍵是否按下
{
  Delay10ms();//延時10ms進行消抖
  if(GPIO_KEY!=0x0f)//再次檢測鍵盤是否按下
  {

//測試列
GPIO_KEY=0X0F;
switch(GPIO_KEY)
{
case(0X07): KeyValue=0;break;
case(0X0b): KeyValue=1;break;
case(0X0d): KeyValue=2;break;
case(0X0e): KeyValue=3;break;
}
//測試行
GPIO_KEY=0XF0;
switch(GPIO_KEY)
{
case(0X70): KeyValue=KeyValue;break;
case(0Xb0): KeyValue=KeyValue+4;break;
case(0Xd0): KeyValue=KeyValue+8;break;
case(0Xe0): KeyValue=KeyValue+12;break;
}
while((a<50)&&(GPIO_KEY!=0xf0))  //檢測按鍵松手檢測
{
Delay10ms();
a++;
}
  }
}

return KeyValue;
}
/**********************************************
功能說明：讀取按鍵動作
入口參數：無
出口參數：返回按鍵動作
注意：
沒有按鍵動作，則返回0，
使用矩陣按鍵:向上S12；向下S6;向左S12;向右S9;
***********************************************/
unsigned char OSReadKey(void)
{
static unsigned char KeyEventCnt=0;
static unsigned char KeySampleCnt=0;
static unsigned char KeyBuffer=0;
#define SHORT_ON_DITHERING_COUNTER 3//定義短按按下去抖時間
#define SHORT_OFF_DITHERING_COUNTER 3//定義短按松開去抖時間，一般與短按按下去抖時間相同
#if OS_LONG_EYK_EN>0
static unsigned int LongKeySampleCnt=0;
#define LONG_ON_DITHERING_COUNTER 250//定義長按按下確認需要的時間，如果是每1MS調用一次OSReadKey()，則1000意味著這個時間為1S
#define LONG_OFF_DITHERING_COUNTER 3//定義長按松開去抖時間，一般和短按去抖時間相同
#endif
unsigned char KeyTemp;
KeyTemp=DIG_CODE[KeyDown()];
switch(KeyEventCnt)
{
  case 0:
if(KeyTemp!=0)
{
KeySampleCnt=0;
KeyBuffer=KeyTemp;
KeyEventCnt=1;
}
return 0;//no key on,return 0
break;

  #if OS_LONG_EYK_EN>0
  case 1:
if(KeyTemp!=KeyBuffer)
{
KeyEventCnt=0;
return 0;//is dithering,return 0
}
else
{
if(++KeySampleCnt>SHORT_ON_DITHERING_COUNTER)
{
   KeySampleCnt=0;
   KeyEventCnt=2;
   LongKeySampleCnt=0;
   return ((KeyBuffer-1)<<2)+1;//sure that key on,return (KeyBuffer-1)<<2+1
}
else
   return 0;//not sure that key on,return 0
}
break;

  case 2:
if(++LongKeySampleCnt>LONG_ON_DITHERING_COUNTER)
{
KeySampleCnt=0;
KeyEventCnt=3;
return ((KeyBuffer-1)<<2)+2; //sure that key long on,return (KeyBuffer-1)<<2+2
}
else
{
if(KeyTemp!=KeyBuffer)
{
   if(++KeySampleCnt>SHORT_OFF_DITHERING_COUNTER)
   {
   KeyEventCnt=0;
   return ((KeyBuffer-1)<<2)+3;//after short on to off,(KeyBuffer-1)<<2+3
   }
   else
   return 0;
}
else
{
   KeySampleCnt=0;
   return 0;
}
}
break;

  case 3:
if(KeyTemp!=KeyBuffer)
{
if(++KeySampleCnt>LONG_OFF_DITHERING_COUNTER)
{
   KeyEventCnt=0;
   return ((KeyBuffer-1)<<2)+4;  //after long key on turn to off,(KeyBuffer-1)<<2+4
}
else
   return 0;
}
else
{
KeySampleCnt=0;
return 0;
}
break;

  #else
  case 1:
if(KeyTemp!=KeyBuffer)
{
KeyEventCnt=0;
return 0;//is dithering,return 0
}
else
{
if(++KeySampleCnt>=SHORT_ON_DITHERING_COUNTER)
{
   KeySampleCnt=0;
   KeyEventCnt=2;
   return ((KeyBuffer-1)<<2)+1;//sure that key on,return (KeyBuffer-1)<<2+1
}
else
   return 0;//not sure that key on,return 0
}
break;

  case 2:
if(KeyTemp!=KeyBuffer)
{
if(++KeySampleCnt>=SHORT_OFF_DITHERING_COUNTER)
{
   KeyEventCnt=0;
   return ((KeyBuffer-1)<<2)+3;//after short on to off,(KeyBuffer-1)<<2+3
}
else
   return 0;
}
else
{
KeySampleCnt=0;
return 0;
}
break;
  #endif
  default:break;
}
return 0;
}

/************************************
偽隨機數發生器
*************************************/
double Random(void)
{
long TmpSeed;
TmpSeed=A*(Seed%Q)-R*(Seed/Q);
if(TmpSeed>=0)
Seed=TmpSeed;
else
Seed=TmpSeed+M;
return (double)Seed/M;
}
/**************************************
為偽隨機數發生器播種
***************************************/
void InitRandom(unsigned long InitVal)
{
Seed=InitVal;
}
/*********************************
初始化MPU
**********************************/
void InitCpu(void)
{
TMOD=0x01;
TH0=0;
TL0=0;
TR0=1;
ET0=1;
EA=1;
}
void Timer0Int(void) interrupt 1
{
switch(OSReadKey())
{
case 5:
KeyBuffer=FUNC;       //表示級別
break;
case 21:
KeyBuffer=DOWN;    //表示右
break;
case 13:
KeyBuffer=UP;    //表示左
break;
case 9:
KeyBuffer=RIGHT;    //表示上
break;
case 17:
KeyBuffer=LEFT;    //表示下
break;
default:
break;
}
}
/******************************
畫墻壁，初始化界面
*******************************/
void DrawBoardf()
{
unsigned char n;
for(n=0;n<31;n++)
  {
Lcd_Rectangle(3*n,0,3*n+2,2,1);
Lcd_Rectangle(3*n,60,3*n+2,62,1);
  }
for(n=0;n<21;n++)
  {
Lcd_Rectangle(0,3*n,2,3*n+2,1);
Lcd_Rectangle(90,3*n,92,3*n+2,1);
  }
Lcd_HoriLine(93,31,35,1);
Lcd_HoriLine(93,63,35,1);
}
void Drawboardt(void)
{
unsigned char n;
for(n=0;n<21;n++)
{
Lcd_Rectangle(0,3*n,2,3*n+2,1);
Lcd_Rectangle(90,3*n,92,3*n+2,1);
}
Lcd_HoriLine(93,31,35,1);
Lcd_HoriLine(93,63,35,1);
}

/***************************
打印成績
****************************/
void PrintScore(void)
{
unsigned char Str[3];
Lcd_WriteStr(6,0,"成績");
Str[0]=(Score/10)|0x30;//十位
Str[1]=(Score%10)|0x30;//個位
Str[2]=0;
Lcd_WriteStr(7,1,Str);
}
/********************************
打印速度級別
*********************************/
void PrintSpeed(void)
{
unsigned char Str[2];
Lcd_WriteStr(6,2,"級別");
Str[0]=Speed_tiaosu|0x30;
Str[1]=0;
Lcd_WriteStr(7,3,Str);
}
/***********************************
游戲結束處理
************************************/
void GameOver(void)
{
unsigned char n;
Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,0);//消隱出食物
for(n=1;n<snake.node;n++)
{
Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,0);//消隱食物，蛇頭已到墻壁內，故不用消去
}
if(snake.life==0)//如果蛇還活著
Lcd_WriteStr(2,1,"過關");
else          //如果蛇死了
Lcd_WriteStr(2,1,"輸了");
Lcd_WriteStr(1,2,"游戲結束");
}
/********************************
游戲的具體過程，也是貪吃蛇算法的關鍵部分
*********************************/
void GamePlayf(void)
{
unsigned char n;
InitRandom(TL0);
food.yes=1;//1表示需要出現新事物，0表示已經存在食物尚未吃掉
snake.life=0;//表示蛇還活著
snake.direction=DOWN;
snake.x[0]=6;snake.y[0]=6;
snake.x[1]=3;snake.y[1]=6;
snake.node=2;
PrintScore();
PrintSpeed();
while(1)
{
if(food.yes==1)
{
  while(1)
  {
food.x=Random()*85+3;
food.y=Random()*55+3;//獲得隨機數
while(food.x%3!=0)
food.x++;
while(food.y%3!=0)
food.y++;
   for(n=0;n<snake.node;n++)//判斷產生的食物坐標是否和蛇身重合
{
if((food.x==snake.x[n])&&(food.y==snake.y[n]))
   break;
}
if(n==snake.node)
{
food.yes=0;
break;//產生有效的食物坐標
}
  }
}
if(food.yes==0)
{
  Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,1);
}
for(n=snake.node-1;n>0;n--)
{
  snake.x[n]=snake.x[n-1];
  snake.y[n]=snake.y[n-1];
}
switch(snake.direction)
{
  case DOWN:snake.x[0]+=3;break;
  case UP:snake.x[0]-=3;break;
  case RIGHT:snake.y[0]-=3;break;
  case LEFT:snake.y[0]+=3;break;
  default:break;
}
for(n=3;n<snake.node;n++)//從第三節開始判斷蛇頭是否咬到自己
{
  if(snake.x[n]==snake.x[0]&&snake.y[n]==snake.y[0])
  {
GameOver();
snake.life=1;
break;
  }
}
if(snake.x[0]<3||snake.x[0]>=90||snake.y[0]<3||snake.y[0]>=60)//判蛇頭是否撞到墻壁
{
  GameOver();
  snake.life=1;
}
if(snake.life==1)
  break;//蛇死，則跳出while(1)循環
if(snake.x[0]==food.x&&snake.y[0]==food.y)//判蛇是否吃到食物
{
  Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,0);//消隱食物
  snake.x[snake.node]=200;
  snake.y[snake.node]=200;//產生蛇新的節坐標先放在看不見的位置
  snake.node++;//蛇節數加1
  food.yes=1;//食物標志置1
  if(++Score>=PASSSCORE)
  {
PrintScore();
GameOver();
break;
  }
  PrintScore();
}
for(n=0;n<snake.node;n++)
{
  Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
}//根據蛇的節數畫出蛇
delay(Speed_tiaosu*1000); //調速
delay(Speed_tiaosu*1000);
Lcd_Rectangle(snake.x[snake.node-1],snake.y[snake.node-1],snake.x[snake.node-1]+2,snake.y[snake.node-1]+2,0);
switch(KeyBuffer)
{
  case FUNC:
KeyBuffer=0;
if(++Speed_tiaosu>=10)
   Speed_tiaosu=1;
   PrintSpeed();
break;
  case DOWN:
KeyBuffer=0;
if(snake.direction!=UP)
   snake.direction=DOWN;
break;
  case UP:
KeyBuffer=0;
if(snake.direction!=DOWN)
   snake.direction=UP;
break;
  case RIGHT:
KeyBuffer=0;
if(snake.direction!=LEFT)
   snake.direction=RIGHT;
break;
   case LEFT:
KeyBuffer=0;
if(snake.direction!=RIGHT)
   snake.direction=LEFT;
break;
  default:
break;
}
}
}
void Gameplayt(void)
{
unsigned char n;
InitRandom(TL0);
food.yes=1;//1表示需要出現新事物，0表示已經存在食物尚未吃掉
snake.life=0;//表示蛇還活著
snake.direction=DOWN;
snake.x[0]=6;snake.y[0]=6;
snake.x[1]=3;snake.y[1]=6;
snake.node=2;
PrintScore();
PrintSpeed();
while(1)
{
if(food.yes==1)
{
  while(1)
  {
food.x=Random()*85+3;
food.y=Random()*55+3;//獲得隨機數
while(food.x%3!=0)
food.x++;
while(food.y%3!=0)
food.y++;
   for(n=0;n<snake.node;n++)//判斷產生的食物坐標是否和蛇身重合
{
if((food.x==snake.x[n])&&(food.y==snake.y[n]))
   break;
}
if(n==snake.node)
{
food.yes=0;
break;//產生有效的食物坐標
}
  }
}
if(food.yes==0)
{
  Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,1);
}
for(n=snake.node-1;n>0;n--)
{
  snake.x[n]=snake.x[n-1];
  snake.y[n]=snake.y[n-1];
}
switch(snake.direction)
{
  case DOWN:snake.x[0]+=3;break;
  case UP:snake.x[0]-=3;break;
  case RIGHT:snake.y[0]-=3;break;
  case LEFT:snake.y[0]+=3;break;
  default:break;
}
for(n=3;n<snake.node;n++)//從第三節開始判斷蛇頭是否咬到自己
{
  if(snake.x[n]==snake.x[0]&&snake.y[n]==snake.y[0])
  {
GameOver();
snake.life=1;
break;
  }
}
if(snake.x[0]<3||snake.x[0]>=90)//判蛇頭是否撞到墻壁
{
  GameOver();
  snake.life=1;
}
if(snake.life==1)
  break;//蛇死，則跳出while(1)循環
if(snake.y[0]<3||snake.y[0]>=60)
{  if(snake.y[0]<3)
snake.y[0]=59;
//    for(n=0;n<snake.node;n++)
//  {
// Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
//  }//根據蛇的節數畫出蛇
if(snake.y[0]>=60)
snake.y[0]=3;
// for(n=0;n<snake.node;n++)
//  {
// Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
//  }//根據蛇的節數畫出蛇
//

}
if(snake.x[0]==food.x&&snake.y[0]==food.y)//判蛇是否吃到食物
{
  Lcd_Rectangle(food.x,food.y,food.x+2,food.y+2,0);//消隱食物
  snake.x[snake.node]=200;
  snake.y[snake.node]=200;//產生蛇新的節坐標先放在看不見的位置
  snake.node++;//蛇節數加1
  food.yes=1;//食物標志置1
  if(++Score>=PASSSCORE)
  {
PrintScore();
GameOver();
break;
  }
  PrintScore();
}
for(n=0;n<snake.node;n++)
{
  Lcd_Rectangle(snake.x[n],snake.y[n],snake.x[n]+2,snake.y[n]+2,1);
}//根據蛇的節數畫出蛇
delay(Speed_tiaosu*1000); //調速
delay(Speed_tiaosu*1000);
Lcd_Rectangle(snake.x[snake.node-1],snake.y[snake.node-1],snake.x[snake.node-1]+2,snake.y[snake.node-1]+2,0);
switch(KeyBuffer)
{
  case FUNC:
KeyBuffer=0;
if(++Speed_tiaosu>=10)
   Speed_tiaosu=1;
   PrintSpeed();
break;
  case DOWN:
KeyBuffer=0;
if(snake.direction!=UP)
   snake.direction=DOWN;
break;
  case UP:
KeyBuffer=0;
if(snake.direction!=DOWN)
   snake.direction=UP;
break;
  case RIGHT:
KeyBuffer=0;
if(snake.direction!=LEFT)
   snake.direction=RIGHT;
break;
   case LEFT:
KeyBuffer=0;
if(snake.direction!=RIGHT)
   snake.direction=LEFT;
break;
  default:
break;
}
}
}

void scankey(void)
{

}

void speed(void)
{
Lcd_WriteStr(0,1,"Speed1");

Lcd_WriteStr(1,1,"Speed2");

Lcd_WriteStr(2,1,"Speed3");

Lcd_WriteStr(3,1,"Speed4");
}
void moshi(void)
{
Lcd_WriteStr(0,1,"mosho1");

Lcd_WriteStr(1,1,"moshi2");
}
void zhujiemian(void)
{
Lcd_WriteCmd(0x01);
  Lcd_WriteStr(0,0,"開始游戲");
Lcd_WriteStr(0,1,"速度選擇");
Lcd_WriteStr(0,2,"模式設置");
}
unsigned char moshi1()
{
moshiceshi=1;
DrawBoardf();
GamePlayf();
return moshiceshi;
zhujiemian();
}
unsigned char moshi2()
{
moshiceshi=2;
  Drawboardt();
  Gameplayt();
return moshiceshi;
zhujiemian();
}
void Speed1(void)
{
unsigned char Speed_tiaosu=1;
zhujiemian();
}
void Speed2(void)
{
unsigned char Speed_tiaosu=2;
zhujiemian();

}
void Speed3(void)
{
unsigned char Speed_tiaosu=3;
zhujiemian();

}
void Speed4(void)
{
unsigned char Speed_tiaosu=4;
zhujiemian();
}
void game(void)
{
  InitCpu();//初始化CPU
Lcd_Reset(); //初始化LCD屏
delay(5000);
Lcd_Clear(0);//清屏
switch(Speed_tiaosu)
{
  case '1':
  Speed1();
  break;
  case '2':
  Speed2();
  break;
  case '3':
  Speed3();
  break;
  case '4':
  Speed4();
  break;
  default:
  Speed4();
}
switch(moshiceshi)
{
  case '1':
  moshi1();
  break;
  case '2':
  moshi2();
  break;
  default:
  moshi1();
}
GameOver();//游戲結束
}

作者: lynn710 時間: 2018-8-15 02:36
這是修改后的代碼，為什么程序會卡住呢？？？

歡迎光臨 (http://www.raoushi.com/bbs/)