亚洲欧洲国产伦综合,欧美日韩精品视频在线一区二区,五月婷婷丁香激情

#ifndef _STC15Fxxxx_H
#define _STC15Fxxxx_H
#include <intrins.h>
/* BYTE Registers */
sfr P0 = 0x80;
sfr SP = 0x81;
sfr DPL = 0x82;
sfr DPH = 0x83;
sfr S4CON = 0x84;
sfr S4BUF = 0x85;
sfr PCON = 0x87;
sfr TCON = 0x88;
sfr TMOD = 0x89;
sfr TL0 = 0x8A;
sfr TL1 = 0x8B;
sfr TH0 = 0x8C;
sfr TH1 = 0x8D;
sfr AUXR = 0x8E;
sfr WAKE_CLKO = 0x8F;
sfr INT_CLKO = 0x8F;
sfr AUXR2 = 0x8F;
sfr RL_TL0 = 0x8A;
sfr RL_TL1 = 0x8B;
sfr RL_TH0 = 0x8C;
sfr RL_TH1 = 0x8D;
sfr P1 = 0x90;
sfr P1M1 = 0x91; //P1M1.n,P1M0.n =00--->Standard, 01--->push-pull 實際上1T的都一樣
sfr P1M0 = 0x92; // =10--->pure input, 11--->open drain
sfr P0M1 = 0x93; //P0M1.n,P0M0.n =00--->Standard, 01--->push-pull
sfr P0M0 = 0x94; // =10--->pure input, 11--->open drain
sfr P2M1 = 0x95; //P2M1.n,P2M0.n =00--->Standard, 01--->push-pull
sfr P2M0 = 0x96; // =10--->pure input, 11--->open drain
sfr CLK_DIV = 0x97;
sfr PCON2 = 0x97;
sfr SCON = 0x98;
sfr SBUF = 0x99;
sfr S2CON = 0x9A; //
sfr S2BUF = 0x9B; //
sfr P1ASF = 0x9D; //只寫，模擬輸入(AD或LVD)選擇
sfr P2 = 0xA0;
sfr BUS_SPEED = 0xA1;
sfr AUXR1 = 0xA2;
sfr P_SW1 = 0xA2;
sfr IE = 0xA8;
sfr SADDR = 0xA9;
sfr WKTCL = 0xAA; //喚醒定時器低字節
sfr WKTCH = 0xAB; //喚醒定時器高字節
sfr S3CON = 0xAC;
sfr S3BUF = 0xAD;
sfr IE2 = 0xAF; //STC12C5A60S2系列
sfr P3 = 0xB0;
sfr P3M1 = 0xB1; //P3M1.n,P3M0.n =00--->Standard, 01--->push-pull
sfr P3M0 = 0xB2; // =10--->pure input, 11--->open drain
sfr P4M1 = 0xB3; //P4M1.n,P4M0.n =00--->Standard, 01--->push-pull
sfr P4M0 = 0xB4; // =10--->pure input, 11--->open drain
sfr IP2 = 0xB5; //STC12C5A60S2系列
sfr IPH2 = 0xB6; //STC12C5A60S2系列
sfr IPH = 0xB7;
sfr IP = 0xB8;
sfr SADEN = 0xB9;
sfr P_SW2 = 0xBA;
sfr ADC_CONTR = 0xBC; //帶AD系列
sfr ADC_RES = 0xBD; //帶AD系列
sfr ADC_RESL = 0xBE; //帶AD系列
sfr P4 = 0xC0;
sfr WDT_CONTR = 0xC1;
sfr IAP_DATA = 0xC2;
sfr IAP_ADDRH = 0xC3;
sfr IAP_ADDRL = 0xC4;
sfr IAP_CMD = 0xC5;
sfr IAP_TRIG = 0xC6;
sfr IAP_CONTR = 0xC7;
sfr ISP_DATA = 0xC2;
sfr ISP_ADDRH = 0xC3;
sfr ISP_ADDRL = 0xC4;
sfr ISP_CMD = 0xC5;
sfr ISP_TRIG = 0xC6;
sfr ISP_CONTR = 0xC7;
sfr P5 = 0xC8; //
sfr P5M1 = 0xC9; // P5M1.n,P5M0.n =00--->Standard, 01--->push-pull
sfr P5M0 = 0xCA; // =10--->pure input, 11--->open drain
sfr P6M1 = 0xCB; // P5M1.n,P5M0.n =00--->Standard, 01--->push-pull
sfr P6M0 = 0xCC; // =10--->pure input, 11--->open drain
sfr SPSTAT = 0xCD; //
sfr SPCTL = 0xCE; //
sfr SPDAT = 0xCF; //
sfr PSW = 0xD0;
sfr T4T3M = 0xD1;
sfr T4H = 0xD2;
sfr T4L = 0xD3;
sfr T3H = 0xD4;
sfr T3L = 0xD5;
sfr T2H = 0xD6;
sfr T2L = 0xD7;
sfr TH4 = 0xD2;
sfr TL4 = 0xD3;
sfr TH3 = 0xD4;
sfr TL3 = 0xD5;
sfr TH2 = 0xD6;
sfr TL2 = 0xD7;
sfr RL_T4H = 0xD2;
sfr RL_T4L = 0xD3;
sfr RL_T3H = 0xD4;
sfr RL_T3L = 0xD5;
sfr RL_T2H = 0xD6;
sfr RL_T2L = 0xD7;
sfr CCON = 0xD8; //
sfr CMOD = 0xD9; //
sfr CCAPM0 = 0xDA; //PCA模塊0的工作模式寄存器。
sfr CCAPM1 = 0xDB; //PCA模塊1的工作模式寄存器。
sfr CCAPM2 = 0xDC; //PCA模塊2的工作模式寄存器。
sfr ACC = 0xE0;
sfr P7M1 = 0xE1;
sfr P7M0 = 0xE2;
sfr P6 = 0xE8;
sfr CL = 0xE9; //
sfr CCAP0L = 0xEA; //PCA模塊0的捕捉/比較寄存器低8位。
sfr CCAP1L = 0xEB; //PCA模塊1的捕捉/比較寄存器低8位。
sfr CCAP2L = 0xEC; //PCA模塊2的捕捉/比較寄存器低8位。
sfr B = 0xF0;
sfr PCA_PWM0 = 0xF2; //PCA模塊0 PWM寄存器。
sfr PCA_PWM1 = 0xF3; //PCA模塊1 PWM寄存器。
sfr PCA_PWM2 = 0xF4; //PCA模塊2 PWM寄存器。
sfr P7 = 0xF8;
sfr CH = 0xF9;
sfr CCAP0H = 0xFA; //PCA模塊0的捕捉/比較寄存器高8位。
sfr CCAP1H = 0xFB; //PCA模塊1的捕捉/比較寄存器高8位。
sfr CCAP2H = 0xFC; //PCA模塊2的捕捉/比較寄存器高8位。
/* BIT Registers */
/* PSW */
sbit CY = PSW^7;
sbit AC = PSW^6;
sbit F0 = PSW^5;
sbit RS1 = PSW^4;
sbit RS0 = PSW^3;
sbit OV = PSW^2;
sbit F1 = PSW^1;
sbit P = PSW^0;
/* TCON */
sbit TF1 = TCON^7; //定時器1溢出中斷標志位
sbit TR1 = TCON^6; //定時器1運行控制位
sbit TF0 = TCON^5; //定時器0溢出中斷標志位
sbit TR0 = TCON^4; //定時器0運行控制位
sbit IE1 = TCON^3; //外中斷1標志位
sbit IT1 = TCON^2; //外中斷1信號方式控制位，1：下降沿中斷，0：上升下降均中斷。
sbit IE0 = TCON^1; //外中斷0標志位
sbit IT0 = TCON^0; //外中斷0信號方式控制位，1：下降沿中斷，0：上升下降均中斷。
/* P0 */
sbit P00 = P0^0;
sbit P01 = P0^1;
sbit P02 = P0^2;
sbit P03 = P0^3;
sbit P04 = P0^4;
sbit P05 = P0^5;
sbit P06 = P0^6;
sbit P07 = P0^7;
/* P1 */
sbit P10 = P1^0;
sbit P11 = P1^1;
sbit P12 = P1^2;
sbit P13 = P1^3;
sbit P14 = P1^4;
sbit P15 = P1^5;
sbit P16 = P1^6;
sbit P17 = P1^7;
sbit RXD2 = P1^0;
sbit TXD2 = P1^1;
sbit CCP1 = P1^0;
sbit CCP0 = P1^1;
sbit SPI_SS = P1^2;
sbit SPI_MOSI = P1^3;
sbit SPI_MISO = P1^4;
sbit SPI_SCLK = P1^5;
sbit SPI_SS_2 = P2^4;
sbit SPI_MOSI_2 = P2^3;
sbit SPI_MISO_2 = P2^2;
sbit SPI_SCLK_2 = P2^1;
sbit SPI_SS_3 = P5^4;
sbit SPI_MOSI_3 = P4^0;
sbit SPI_MISO_3 = P4^1;
sbit SPI_SCLK_3 = P4^3;
/* P2 */
sbit P20 = P2^0;
sbit P21 = P2^1;
sbit P22 = P2^2;
sbit P23 = P2^3;
sbit P24 = P2^4;
sbit P25 = P2^5;
sbit P26 = P2^6;
sbit P27 = P2^7;
/* P3 */
sbit P30 = P3^0;
sbit P31 = P3^1;
sbit P32 = P3^2;
sbit P33 = P3^3;
sbit P34 = P3^4;
sbit P35 = P3^5;
sbit P36 = P3^6;
sbit P37 = P3^7;
sbit RXD = P3^0;
sbit TXD = P3^1;
sbit INT0 = P3^2;
sbit INT1 = P3^3;
sbit T0 = P3^4;
sbit T1 = P3^5;
sbit WR = P3^6;
sbit RD = P3^7;
sbit CCP2 = P3^7;
sbit CLKOUT0 = P3^5;
sbit CLKOUT1 = P3^4;
/* P4 */
sbit P40 = P4^0;
sbit P41 = P4^1;
sbit P42 = P4^2;
sbit P43 = P4^3;
sbit P44 = P4^4;
sbit P45 = P4^5;
sbit P46 = P4^6;
sbit P47 = P4^7;
/* P5 */
sbit P50 = P5^0;
sbit P51 = P5^1;
sbit P52 = P5^2;
sbit P53 = P5^3;
sbit P54 = P5^4;
sbit P55 = P5^5;
sbit P56 = P5^6;
sbit P57 = P5^7;
/* SCON */
sbit SM0 = SCON^7; //SM0/FE SM0 SM1 = 00 ~ 11: 方式0~3
sbit SM1 = SCON^6; //
sbit SM2 = SCON^5; //多機通訊
sbit REN = SCON^4; //接收允許
sbit TB8 = SCON^3; //發送數據第8位
sbit RB8 = SCON^2; //接收數據第8位
sbit TI = SCON^1; //發送中斷標志位
sbit RI = SCON^0; //接收中斷標志位
/* IE */
sbit EA = IE^7; //中斷允許總控制位
sbit ELVD = IE^6; //低壓監測中斷允許位
sbit EADC = IE^5; //ADC 中斷允許位
sbit ES = IE^4; //串行中斷允許控制位
sbit ET1 = IE^3; //定時中斷1允許控制位
sbit EX1 = IE^2; //外部中斷1允許控制位
sbit ET0 = IE^1; //定時中斷0允許控制位
sbit EX0 = IE^0; //外部中斷0允許控制位
/* IP */
/*
sbit PPCA = IP^7; //PCA 中斷優先級設定位
sbit PLVD = IP^6; //低壓中斷優先級設定位
sbit PADC = IP^5; //ADC 中斷優先級設定位
sbit PS = IP^4; //串行中斷0優先級設定位
sbit PT1 = IP^3; //定時中斷1優先級設定位
sbit PX1 = IP^2; //外部中斷1優先級設定位
sbit PT0 = IP^1; //定時中斷0優先級設定位
sbit PX0 = IP^0; //外部中斷0優先級設定位
*/
sbit ACC0 = ACC^0;
sbit ACC1 = ACC^1;
sbit ACC2 = ACC^2;
sbit ACC3 = ACC^3;
sbit ACC4 = ACC^4;
sbit ACC5 = ACC^5;
sbit ACC6 = ACC^6;
sbit ACC7 = ACC^7;
sbit B0 = B^0;
sbit B1 = B^1;
sbit B2 = B^2;
sbit B3 = B^3;
sbit B4 = B^4;
sbit B5 = B^5;
sbit B6 = B^6;
sbit B7 = B^7;
// 7 6 5 4 3 2 1 0 Reset Value
//sfr IE2 = 0xAF; - - - - - - ESPI ES2 0000,0000B //Auxiliary Interrupt
#define SPI_INT_ENABLE() IE2 |= 2 //允許SPI中斷
#define SPI_INT_DISABLE() IE2 &= ~2 //允許SPI中斷
#define UART2_INT_ENABLE() IE2 |= 1 //允許串口2中斷
#define UART2_INT_DISABLE() IE2 &= ~1 //允許串口2中斷
// 7 6 5 4 3 2 1 0 Reset Value
//sfr IP = 0xB8; //中斷優先級低位 PPCA PLVD PADC PS PT1 PX1 PT0 PX0 0000,0000
//--------
sbit PPCA = IP^7; //PCA 模塊中斷優先級
sbit PLVD = IP^6; //低壓監測中斷優先級
sbit PADC = IP^5; //ADC 中斷優先級
sbit PS = IP^4; //串行中斷0優先級設定位
sbit PT1 = IP^3; //定時中斷1優先級設定位
sbit PX1 = IP^2; //外部中斷1優先級設定位
sbit PT0 = IP^1; //定時中斷0優先級設定位
sbit PX0 = IP^0; //外部中斷0優先級設定位
// 7 6 5 4 3 2 1 0 Reset Value
//sfr IPH = 0xB7; //中斷優先級高位 PPCAH PLVDH PADCH PSH PT1H PX1H PT0H PX0H 0000,0000
//sfr IP2 = 0xB5; // - - - - - - PSPI PS2 xxxx,xx00
//sfr IPH2 = 0xB6; // - - - - - - PSPIH PS2H xxxx,xx00
#define PPCAH 0x80
#define PLVDH 0x40
#define PADCH 0x20
#define PSH 0x10
#define PT1H 0x08
#define PX1H 0x04
#define PT0H 0x02
#define PX0H 0x01
#define PCA_InterruptFirst() PPCA = 1
#define LVD_InterruptFirst() PLVD = 1
#define ADC_InterruptFirst() PADC = 1
#define UART1_InterruptFirst() PS = 1
#define Timer1_InterruptFirst() PT1 = 1
#define INT1_InterruptFirst() PX1 = 1
#define Timer0_InterruptFirst() PT0 = 1
#define INT0_InterruptFirst() PX0 = 1
/*************************************************************************************************/
#define S1_DoubleRate() PCON |= 0x80
#define S1_SHIFT() SCON &= 0x3f
#define S1_8bit() SCON |= 0x40
#define S1_9bit() SCON |= 0xc0
#define S1_RX_Enable() SCON |= 0x10
#define S1_USE_P30P31() P_SW1 &= ~0xc0 //UART1 使用P30 P31口默認
#define S1_USE_P36P37() P_SW1 = (P_SW1 & ~0xc0) | 0x40 //UART1 使用P36 P37口
#define S1_USE_P16P17() P_SW1 = (P_SW1 & ~0xc0) | 0x80 //UART1 使用P16 P17口
#define S1_TXD_RXD_SHORT() PCON2 |= (1<<4) //將TXD與RXD連接中繼輸出
#define S1_TXD_RXD_OPEN() PCON2 |= (1<<4) //將TXD與RXD連接中繼斷開默認
#define S1_BRT_UseTimer2() AUXR |= 1;
#define S1_BRT_UseTimer1() AUXR &= ~1;
// 7 6 5 4 3 2 1 0 Reset Value
//sfr S2CON = 0x9A; S2SM0 - S2SM2 S2REN S2TB8 S2RB8 S2TI S2RI 00000000B //S2 Control
#define S2_8bit() S2CON &= ~(1<<7) //串口2模式0，8位UART，波特率 = 定時器2的溢出率 / 4
#define S2_9bit() S2CON |= (1<<7) //串口2模式1，9位UART，波特率 = 定時器2的溢出率 / 4
#define S2_RX_Enable() S2CON |= (1<<4) //允許串2接收
#define S2_MODE0() S2CON &= ~(1<<7) //串口2模式0，8位UART，波特率 = 定時器2的溢出率 / 4
#define S2_MODE1() S2CON |= (1<<7) //串口2模式1，9位UART，波特率 = 定時器2的溢出率 / 4
#define S2_RX_EN() S2CON |= (1<<4) //允許串2接收
#define S2_RX_Disable() S2CON &= ~(1<<4) //禁止串2接收
#define TI2 (S2CON & 2) != 0
#define RI2 (S2CON & 1) != 0
#define SET_TI2() S2CON |= 2
#define CLR_TI2() S2CON &= ~2
#define CLR_RI2() S2CON &= ~1
#define S2TB8_SET() S2CON |= 8
#define S2TB8_CLR() S2CON &= ~8
#define S2_Int_en() IE2 |= 1 //串口2允許中斷
#define S2_USE_P10P11() P_SW2 &= ~1 //UART2 使用P1口默認
#define S2_USE_P46P47() P_SW2 |= 1 //UART2 使用P4口
#define S3_USE_P00P01() P_SW2 &= ~2 //UART3 使用P0口默認
#define S3_USE_P50P51() P_SW2 |= 2 //UART3 使用P5口
#define S4_USE_P02P03() P_SW2 &= ~4 //UART4 使用P0口默認
#define S4_USE_P52P53() P_SW2 |= 4 //UART4 使用P5口
/**********************************************************/
#define Timer0_16bitAutoReload() TMOD &= ~0x03 //16位自動重裝
#define Timer0_16bit() TMOD = (TMOD & ~0x03) | 0x01 //16位
#define Timer0_8bitAutoReload() TMOD = (TMOD & ~0x03) | 0x02 //8位自動重裝
#define Timer0_16bitAutoRL_NoMask() TMOD |= 0x03 //16位自動重裝不可屏蔽中斷
#define Timer0_AsCounterP32() TMOD |= 4 //時器0用做計數器
#define Timer0_AsTimer() TMOD &= ~4 //時器0用做定時器
#define Timer0_ExtControlP34() TMOD |= 4 //時器0由外部INT0高電平允許定時計數
#define Timer0_Run() TR0 = 1 //允許定時器0計數
#define Timer0_Stop() TR0 = 0 //禁止定時器0計數
#define Timer0_InterruptEnable() ET0 = 1 //允許Timer1中斷.
#define Timer0_InterruptDisable() ET0 = 0 //禁止Timer1中斷.
#define Timer1_16bitAutoReload() TMOD &= ~0x30 //16位自動重裝
#define Timer1_16bit() TMOD = (TMOD & ~0x30) | 0x10 //16位
#define Timer1_8bitAutoReload() TMOD = (TMOD & ~0x30) | 0x20 //8位自動重裝
#define Timer1_16bitAutoRL_NoMask() TMOD |= 0x30 //16位自動重裝不可屏蔽中斷
#define Timer1_AsCounterP33() TMOD |= (1<<6) //時器1用做計數器
#define Timer1_AsTimer() TMOD &= ~(1<<6) //時器1用做定時器
#define Timer1_ExtControlP35() TMOD |= (1<<7) //時器1由外部INT1高電平允許定時計數
#define Timer1_Run() TR1 = 1 //允許定時器1計數
#define Timer1_Stop() TR1 = 0 //禁止定時器1計數
#define Timer1_InterruptEnable() ET1 = 1 //允許Timer1中斷.
#define Timer1_InterruptDisable() ET1 = 0 //禁止Timer1中斷.
// 7 6 5 4 3 2 1 0 Reset Value
//sfr AUXR = 0x8E; T0x12 T1x12 UART_M0x6 BRTR S2SMOD BRTx12 EXTRAM S1BRS 0000,0000 //Auxiliary Register
#define Timer0_1T() AUXR |= (1<<7) //Timer0 clodk = fo
#define Timer0_12T() AUXR &= ~(1<<7) //Timer0 clodk = fo/12 12分頻, default
#define Timer1_1T() AUXR |= (1<<6) //Timer1 clodk = fo
#define Timer1_12T() AUXR &= ~(1<<6) //Timer1 clodk = fo/12 12分頻, default
#define S1_M0x6() AUXR |= (1<<5) //UART Mode0 Speed is 6x Standard
#define S1_M0x1() AUXR &= ~(1<<5) //default, UART Mode0 Speed is Standard
#define Timer2_Run() AUXR |= (1<<4) //允許定時器2計數
#define Timer2_Stop() AUXR &= ~(1<<4) //禁止定時器2計數
#define Timer2_AsCounterP31() AUXR |= (1<<3) //時器2用做計數器
#define Timer2_AsTimer() AUXR &= ~(1<<3) //時器2用做定時器
#define Timer2_1T() AUXR |= (1<<2) //Timer0 clodk = fo
#define Timer2_12T() AUXR &= ~(1<<2) //Timer0 clodk = fo/12 12分頻, default
#define Timer2_InterruptEnable() IE2 |= (1<<2) //允許Timer2中斷.
#define Timer2_InterruptDisable() IE2 &= ~(1<<2) //禁止Timer2中斷.
#define ExternalRAM_enable() AUXR |= 2 //允許外部XRAM，禁止使用內部1024RAM
#define InternalRAM_enable() AUXR &= ~2 //禁止外部XRAM，允許使用內部1024RAM
#define T0_pulseP34_enable() AUXR2 |= 1 //允許 T0 溢出脈沖在T0(P3.5)腳輸出，Fck0 = 1/2 T0 溢出率，T0可以1T或12T。
#define T0_pulseP34_disable() AUXR2 &= ~1
#define T1_pulseP35_enable() AUXR2 |= 2 //允許 T1 溢出脈沖在T1(P3.4)腳輸出，Fck1 = 1/2 T1 溢出率，T1可以1T或12T。
#define T1_pulseP35_disable() AUXR2 &= ~2
#define T2_pulseP30_enable() AUXR2 |= 4 //允許 T2 溢出脈沖在T1(P3.0)腳輸出，Fck2 = 1/2 T2 溢出率，T2可以1T或12T。
#define T2_pulseP30_disable() AUXR2 &= ~4
#define T0_pulseP35(n) ET0=0,Timer0_AsTimer(),Timer0_1T(),Timer0_16bitAutoReload(),TH0=(65536-(n/2+MAIN_Fosc/2)/(n))/256,TL0=(65536-(n/2+MAIN_Fosc/2)/(n))%256,AUXR2 |= bit0,TR0=1 //fx=fosc/(2*M)/n, M=1 or M=12
#define T1_pulseP34(n) ET1=0,Timer1_AsTimer(),Timer1_1T(),Timer1_16bitAutoReload(),TH1=(65536-(n/2+MAIN_Fosc/2)/(n))/256,TL1=(65536-(n/2+MAIN_Fosc/2)/(n))%256,AUXR2 |= bit1,TR1=1 //fx=fosc/(2*M)/n, M=1 or M=12
#define T2_pulseP30(n) Timer2_InterruptDisable(),Timer2_AsTimer(),Timer2_1T(),TH2=(65536-(n/2+MAIN_Fosc/2)/(n))/256,TL2=(65536-(n/2+MAIN_Fosc/2)/(n))%256,AUXR2 |= bit2,Timer2_Run() //fx=fosc/(2*M)/n, M=1 or M=12
#define Timer0_Load(n) TH0 = (n) / 256, TL0 = (n) % 256
#define Timer1_Load(n) TH1 = (n) / 256, TL1 = (n) % 256
#define Timer2_Load(n) TH2 = (n) / 256, TL2 = (n) % 256
#define Timer0_Load_us(n) TH0=(65536-MainFosc_KHZ*(n)/1000)/256,TL0=(65536-MainFosc_KHZ*(n)/1000)%256
#define Timer1_Load_us(n) TH1=(65536-MainFosc_KHZ*(n)/1000)/256,TL1=(65536-MainFosc_KHZ*(n)/1000)%256
#define Timer2_Load_us(n) TH2=(65536-MainFosc_KHZ*(n)/1000)/256,TL2=(65536-MainFosc_KHZ*(n)/1000)%256
//sfr WDT_CONTR = 0xC1; //Watch-Dog-Timer Control register
// 7 6 5 4 3 2 1 0 Reset Value
// WDT_FLAG - EN_WDT CLR_WDT IDLE_WDT PS2 PS1 PS0 xx00,0000
#define D_WDT_FLAG (1<<7)
#define D_EN_WDT (1<<5)
#define D_CLR_WDT (1<<4) //auto clear
#define D_IDLE_WDT (1<<3) //WDT counter when Idle
#define D_WDT_SCALE_2 0
#define D_WDT_SCALE_4 1
#define D_WDT_SCALE_8 2 //T=393216*N/fo
#define D_WDT_SCALE_16 3
#define D_WDT_SCALE_32 4
#define D_WDT_SCALE_64 5
#define D_WDT_SCALE_128 6
#define D_WDT_SCALE_256 7
#define WDT_reset(n) WDT_CONTR = D_EN_WDT + D_CLR_WDT + D_IDLE_WDT + (n) //初始化WDT，喂狗
// 7 6 5 4 3 2 1 0 Reset Value
//sfr PCON = 0x87; SMOD SMOD0 LVDF POF GF1 GF0 PD IDL 0001,0000 //Power Control
//SMOD //串口雙倍速
//SMOD0
#define LVDF (1<<5) //P4.6低壓檢測標志
//POF
//GF1
//GF0
//#define D_PD 2 //set 1, power down mode
//#define D_IDLE 1 //set 1, idle mode
#define MCU_IDLE() PCON |= 1 //MCU 進入 IDLE 模式
#define MCU_POWER_DOWN() PCON |= 2 //MCU 進入睡眠模式
//sfr ISP_CMD = 0xC5;
#define ISP_STANDBY() ISP_CMD = 0 //ISP空閑命令（禁止）
#define ISP_READ() ISP_CMD = 1 //ISP讀出命令
#define ISP_WRITE() ISP_CMD = 2 //ISP寫入命令
#define ISP_ERASE() ISP_CMD = 3 //ISP擦除命令
//sfr ISP_TRIG = 0xC6;
#define ISP_TRIG() ISP_TRIG = 0x5A, ISP_TRIG = 0xA5 //ISP觸發命令
// 7 6 5 4 3 2 1 0 Reset Value
//sfr IAP_CONTR = 0xC7; IAPEN SWBS SWRST CFAIL - WT2 WT1 WT0 0000,x000 //IAP Control Register
#define ISP_EN (1<<7)
#define ISP_SWBS (1<<6)
#define ISP_SWRST (1<<5)
#define ISP_CMD_FAIL (1<<4)
#define ISP_WAIT_1MHZ 7
#define ISP_WAIT_2MHZ 6
#define ISP_WAIT_3MHZ 5
#define ISP_WAIT_6MHZ 4
#define ISP_WAIT_12MHZ 3
#define ISP_WAIT_20MHZ 2
#define ISP_WAIT_24MHZ 1
#define ISP_WAIT_30MHZ 0
#if (MAIN_Fosc >= 24000000L)
#define ISP_WAIT_FREQUENCY ISP_WAIT_30MHZ
#elif (MAIN_Fosc >= 20000000L)
#define ISP_WAIT_FREQUENCY ISP_WAIT_24MHZ
#elif (MAIN_Fosc >= 12000000L)
#define ISP_WAIT_FREQUENCY ISP_WAIT_20MHZ
#elif (MAIN_Fosc >= 6000000L)
#define ISP_WAIT_FREQUENCY ISP_WAIT_12MHZ
#elif (MAIN_Fosc >= 3000000L)
#define ISP_WAIT_FREQUENCY ISP_WAIT_6MHZ
#elif (MAIN_Fosc >= 2000000L)
#define ISP_WAIT_FREQUENCY ISP_WAIT_3MHZ
#elif (MAIN_Fosc >= 1000000L)
#define ISP_WAIT_FREQUENCY ISP_WAIT_2MHZ
#else
#define ISP_WAIT_FREQUENCY ISP_WAIT_1MHZ
#endif
/* ADC Register */
// 7 6 5 4 3 2 1 0 Reset Value
//sfr ADC_CONTR = 0xBC; ADC_POWER SPEED1 SPEED0 ADC_FLAG ADC_START CHS2 CHS1 CHS0 0000,0000 //AD 轉換控制寄存器
//sfr ADC_RES = 0xBD; ADCV.9 ADCV.8 ADCV.7 ADCV.6 ADCV.5 ADCV.4 ADCV.3 ADCV.2 0000,0000 //A/D 轉換結果高8位
//sfr ADC_RESL = 0xBE; ADCV.1 ADCV.0 0000,0000 //A/D 轉換結果低2位
//sfr ADC_CONTR = 0xBC; //直接用MOV操作，不要用與或
//sfr SPCTL = 0xCE; SPI控制寄存器
// 7 6 5 4 3 2 1 0 Reset Value
// SSIG SPEN DORD MSTR CPOL CPHA SPR1 SPR0 0x00
#define SPI_SSIG_None() SPCTL |= (1<<7) //1: 忽略SS腳
#define SPI_SSIG_Enable() SPCTL &= ~(1<<7) //0: SS腳用于決定主從機
#define SPI_Enable() SPCTL |= (1<<6) //1: 允許SPI
#define SPI_Disable() SPCTL &= ~(1<<6) //0: 禁止SPI
#define SPI_LSB_First() SPCTL |= (1<<5) //1: LSB先發
#define SPI_MSB_First() SPCTL &= ~(1<<5) //0: MSB先發
#define SPI_Master() SPCTL |= (1<<4) //1: 設為主機
#define SPI_Slave() SPCTL &= ~(1<<4) //0: 設為從機
#define SPI_SCLK_NormalH() SPCTL |= (1<<3) //1: 空閑時SCLK為高電平
#define SPI_SCLK_NormalL() SPCTL &= ~(1<<3) //0: 空閑時SCLK為低電平
#define SPI_PhaseH() SPCTL |= (1<<2) //1:
#define SPI_PhaseL() SPCTL &= ~(1<<2) //0:
#define SPI_Speed(n) SPCTL = (SPCTL & ~3) | (n) //設置速度, 0 -- fosc/4, 1 -- fosc/16, 2 -- fosc/64, 3 -- fosc/128
//sfr SPDAT = 0xCF; //SPI Data Register 0000,0000
//sfr SPSTAT = 0xCD; //SPI狀態寄存器
// 7 6 5 4 3 2 1 0 Reset Value
// SPIF WCOL - - - - - -
#define SPIF 0x80 //SPI傳輸完成標志。寫入1清0。
#define WCOL 0x40 //SPI寫沖突標志。寫入1清0。
#define SPI_USE_P12P13P14P15() AUXR1 &= 0x0c //將SPI切換到P12(SS) P13(MOSI) P14(MISO) P15(SCLK)(上電默認)。
#define SPI_USE_P24P23P22P21() AUXR1 = (AUXR1 & ~0x0c) | 0x04 //將SPI切換到P24(SS) P23(MOSI) P22(MISO) P21(SCLK)。
#define SPI_USE_P54P40P41P43() AUXR1 = (AUXR1 & ~0x0c) | 0x08 //將SPI切換到P54(SS) P40(MOSI) P41(MISO) P43(SCLK)。
/*
;PCA_PWMn: 7 6 5 4 3 2 1 0
; EBSn_1 EBSn_0 - - - - EPCnH EPCnL
;B5-B2: 保留
;B1(EPCnH): 在PWM模式下，與CCAPnH組成9位數。
;B0(EPCnL): 在PWM模式下，與CCAPnL組成9位數。
*/
#define PWM0_NORMAL() PCA_PWM0 &= ~3 //PWM0正常輸出(默認)
#define PWM0_OUT_0() PCA_PWM0 |= 3 //PWM0一直輸出0
#define PWM0_OUT_1() PCA_PWM0 &= ~3, CCAP0H = 0; //PWM0一直輸出1
#define PWM1_NORMAL() PCA_PWM1 &= ~3 //PWM0正常輸出(默認)
#define PWM1_OUT_0() PCA_PWM1 |= 3 //PWM0一直輸出0
#define PWM1_OUT_1() PCA_PWM1 &= ~3, CCAP1H = 0; //PWM1一直輸出1
#define PWM2_NORMAL() PCA_PWM2 &= ~3 //PWM1正常輸出(默認)
#define PWM2_OUT_0() PCA_PWM2 |= 3 //PWM2一直輸出0
#define PWM2_OUT_1() PCA_PWM2 &= ~3, CCAP2H = 0; //PWM2一直輸出1
// 7 6 5 4 3 2 1 0 Reset Value
//sfr CCON = 0xD8; CF CR - - - CCF2 CCF1 CCF0 00xx,xx00 //PCA 控制寄存器。
sbit CCF0 = CCON^0; //PCA 模塊0中斷標志，由硬件置位，必須由軟件清0。
sbit CCF1 = CCON^1; //PCA 模塊1中斷標志，由硬件置位，必須由軟件清0。
sbit CCF2 = CCON^2; //PCA 模塊2中斷標志，由硬件置位，必須由軟件清0。
sbit CR = CCON^6; //1: 允許PCA計數器計數，必須由軟件清0。
sbit CF = CCON^7; //PCA計數器溢出（CH，CL由FFFFH變為0000H）標志。PCA計數器溢出后由硬件置位，必須由軟件清0。
// 7 6 5 4 3 2 1 0 Reset Value
//sfr CMOD = 0xD9; CIDL - - - CPS2 CPS1 CPS0 ECF 0xxx,0000 //PCA 工作模式寄存器。
#define PCA_IDLE_OFF() CMOD |= (1<<7) //IDLE狀態PCA停止計數。
#define PCA_IDLE_ON() CMOD &= ~(1<<7) //IDLE狀態PCA繼續計數。
#define PCA_CLK_12T() CMOD &= ~0x0E //PCA計數脈沖選擇外部晶振/12。 fosc/12
#define PCA_CLK_2T() CMOD = (CMOD & ~0x0E) + 2 //PCA計數脈沖選擇外部晶振/2。 fosc/2
#define PCA_CLK_T0() CMOD = (CMOD & ~0x0E) + 4 //PCA計數脈沖選擇Timer0中斷，Timer0可通過AUXR寄存器設置成工作在12T或1T模式。
#define PCA_CLK_ECI() CMOD = (CMOD & ~0x0E) + 6 //PCA計數脈沖選擇從ECI/P3.4腳輸入的外部時鐘，最大 fosc/2。
#define PCA_CLK_1T() CMOD = (CMOD & ~0x0E) + 8 //PCA計數脈沖選擇外部晶振。 Fosc/1
#define PCA_CLK_4T() CMOD = (CMOD & ~0x0E) + 10 //PCA計數脈沖選擇外部晶振/4。 Fosc/4
#define PCA_CLK_6T() CMOD = (CMOD & ~0x0E) + 12 //PCA計數脈沖選擇外部晶振/6。 Fosc/6
#define PCA_CLK_8T() CMOD = (CMOD & ~0x0E) + 14 //PCA計數脈沖選擇外部晶振/8。 Fosc/8
#define PCA_INT_ENABLE() CMOD |= 1 //PCA計數器溢出中斷允許位，1---允許CF（CCON.7）產生中斷。
#define PCA_INT_DISABLE() CMOD &= ~1 //PCA計數器溢出中斷禁止。
// 7 6 5 4 3 2 1 0 Reset Value
//sfr AUXR1 = 0xA2; S1_S1 S1_S0 CCP_S1 CCP_S0 SPI_S1 SPI_S0 - DPS 0100,0000 //Auxiliary Register 1
#define PCA_USE_P12P11P10P37() AUXR1 &= ~0x30 //將PCA/PWM切換到P12(ECI) P11(CCP0) P10(CCP1) P37(CCP2)(上電默認)。
#define PCA_USE_P34P35P36P37() AUXR1 = (AUXR1 & ~0x30) | 0x10 //將PCA/PWM切換到P34(ECI) P35(CCP0) P36(CCP1) P37(CCP2)。
#define PCA_USE_P24P25P26P27() AUXR1 = (AUXR1 & ~0x30) | 0x20 //將PCA/PWM切換到P24(ECI) P25(CCP0) P26(CCP1) P27(CCP2)。
#define DPS_SEL1() AUXR1 |= 1 //1：選擇DPTR1。
#define DPS_SEL0() AUXR1 &= ~1 //0：選擇DPTR0(上電默認)。
/* 7 6 5 4 3 2 1 0 Reset Value
//sfr CCAPM0 = 0xDA; PWM 寄存器 - ECOM0 CAPP0 CAPN0 MAT0 TOG0 PWM0 ECCF0 x000,0000 //PCA 模塊0
//sfr CCAPM1 = 0xDB; PWM 寄存器 - ECOM1 CAPP1 CAPN1 MAT1 TOG1 PWM1 ECCF1 x000,0000 //PCA 模塊1
//sfr CCAPM2 = 0xDC; PWM 寄存器 - ECOM2 CAPP2 CAPN2 MAT2 TOG2 PWM2 ECCF2 x000,0000 //PCA 模塊2
;ECOMn = 1: 允許比較功能。
;CAPPn = 1: 允許上升沿觸發捕捉功能。
;CAPNn = 1: 允許下降沿觸發捕捉功能。
;MATn = 1: 當匹配情況發生時，允許CCON中的CCFn置位。
;TOGn = 1: 當匹配情況發生時，CEXn將翻轉。(CEX0/PCA0/PWM0/P3.7,CEX1/PCA1/PWM1/P3.5)
;PWMn = 1: 將CEXn設置為PWM輸出。
;ECCFn = 1: 允許CCON中的CCFn觸發中斷。
;ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn
; 0 0 0 0 0 0 0 00H 未啟用任何功能。
; x 1 0 0 0 0 x 20H 16位CEXn上升沿觸發捕捉功能。
; x 0 1 0 0 0 x 10H 16位CEXn下降沿觸發捕捉功能。
; x 1 1 0 0 0 x 30H 16位CEXn/PCAn邊沿（上、下沿）觸發捕捉功能。
; 1 0 0 1 0 0 x 48H 16位軟件定時器。
; 1 0 0 1 1 0 x 4CH 16位高速脈沖輸出。
; 1 0 0 0 0 1 0 42H 8位PWM。無中斷
; 1 1 0 0 0 1 1 63H 8位PWM。低變高可產生中斷
; 1 0 1 0 0 1 1 53H 8位PWM。高變低可產生中斷
; 1 1 1 0 0 1 1 73H 8位PWM。低變高或高變低均可產生中斷
;*******************************************************************
;*******************************************************************/
#define PCA0_none() CCAPM0 = 0
#define PCA0_PWM(nbit) CCAPM0 = 0x42,PCA_PWM0 = (PCA_PWM0 & 0x0c) | ((8-nbit)<<6)
#define PCA0_PWM_rise_int(nbit) CCAPM0 = 0x63,PCA_PWM0 = (PCA_PWM0 & 0x0c) | ((8-nbit)<<6)
#define PCA0_PWM_fall_int(nbit) CCAPM0 = 0x53,PCA_PWM0 = (PCA_PWM0 & 0x0c) | ((8-nbit)<<6)
#define PCA0_PWM_edge_int(nbit) CCAPM0 = 0x73,PCA_PWM0 = (PCA_PWM0 & 0x0c) | ((8-nbit)<<6)
#define PCA0_capture_rise() CCAPM0 = (0x20 + 1)
#define PCA0_capture_fall() CCAPM0 = (0x10 + 1)
#define PCA0_capture_edge() CCAPM0 = (0x30 + 1)
#define PCA0_16bit_Timer() CCAPM0 = (0x48 + 1)
#define PCA0_High_Pulse() CCAPM0 = (0x4C + 1)
#define PCA1_none() CCAPM1 = 0
#define PCA1_PWM(nbit) CCAPM1 = 0x42,PCA_PWM1 = (PCA_PWM1 & 0x0c) | ((8-nbit)<<6)
#define PCA1_PWM_rise_int(nbit) CCAPM1 = 0x63,PCA_PWM1 = (PCA_PWM1 & 0x0c) | ((8-nbit)<<6)
#define PCA1_PWM_fall_int(nbit) CCAPM1 = 0x53,PCA_PWM1 = (PCA_PWM1 & 0x0c) | ((8-nbit)<<6)
#define PCA1_PWM_edge_int(nbit) CCAPM1 = 0x73,PCA_PWM1 = (PCA_PWM1 & 0x0c) | ((8-nbit)<<6)
#define PCA1_capture_rise() CCAPM1 = (0x20 + 1)
#define PCA1_capture_fall() CCAPM1 = (0x10 + 1)
#define PCA1_capture_edge() CCAPM1 = (0x30 + 1)
#define PCA1_16bit_Timer() CCAPM1 = (0x48 + 1)
#define PCA1_High_Pulse() CCAPM1 = (0x4C + 1)
#define PCA2_none() CCAPM2 = 0
#define PCA2_PWM(nbit) CCAPM2 = 0x42,PCA_PWM2 = (PCA_PWM2 & 0x0c) | ((8-nbit)<<6)
#define PCA2_PWM_rise_int(nbit) CCAPM2 = 0x63,PCA_PWM2 = (PCA_PWM2 & 0x0c) | ((8-nbit)<<6)
#define PCA2_PWM_fall_int(nbit) CCAPM2 = 0x53,PCA_PWM2 = (PCA_PWM2 & 0x0c) | ((8-nbit)<<6)
#define PCA2_PWM_edge_int(nbit) CCAPM2 = 0x73,PCA_PWM2 = (PCA_PWM2 & 0x0c) | ((8-nbit)<<6)
#define PCA2_capture_rise() CCAPM2 = (0x20 + 1)
#define PCA2_capture_fall() CCAPM2 = (0x10 + 1)
#define PCA2_capture_edge() CCAPM2 = (0x30 + 1)
#define PCA2_16bit_Timer() CCAPM2 = (0x48 + 1)
#define PCA2_High_Pulse() CCAPM2 = (0x4C + 1)
/* Above is STC additional SFR or change */
/**********************************************************/
typedef unsigned char u8;
typedef unsigned int u16;
typedef unsigned long u32;
/**********************************************************/
#define NOP1() _nop_()
#define NOP2() NOP1(),NOP1()
#define NOP3() NOP2(),NOP1()
#define NOP4() NOP3(),NOP1()
#define NOP5() NOP4(),NOP1()
#define NOP6() NOP5(),NOP1()
#define NOP7() NOP6(),NOP1()
#define NOP8() NOP7(),NOP1()
#define NOP9() NOP8(),NOP1()
#define NOP10() NOP9(),NOP1()
#define NOP11() NOP10(),NOP1()
#define NOP12() NOP11(),NOP1()
#define NOP13() NOP12(),NOP1()
#define NOP14() NOP13(),NOP1()
#define NOP15() NOP14(),NOP1()
#define NOP16() NOP15(),NOP1()
#define NOP17() NOP16(),NOP1()
#define NOP18() NOP17(),NOP1()
#define NOP19() NOP18(),NOP1()
#define NOP20() NOP19(),NOP1()
#define NOP21() NOP20(),NOP1()
#define NOP22() NOP21(),NOP1()
#define NOP23() NOP22(),NOP1()
#define NOP24() NOP23(),NOP1()
#define NOP25() NOP24(),NOP1()
#define NOP26() NOP25(),NOP1()
#define NOP27() NOP26(),NOP1()
#define NOP28() NOP27(),NOP1()
#define NOP29() NOP28(),NOP1()
#define NOP30() NOP29(),NOP1()
#define NOP31() NOP30(),NOP1()
#define NOP32() NOP31(),NOP1()
#define NOP33() NOP32(),NOP1()
#define NOP34() NOP33(),NOP1()
#define NOP35() NOP34(),NOP1()
#define NOP36() NOP35(),NOP1()
#define NOP37() NOP36(),NOP1()
#define NOP38() NOP37(),NOP1()
#define NOP39() NOP38(),NOP1()
#define NOP40() NOP39(),NOP1()
#define NOP(N) NOP##N()
/**********************************************/
/****************************************************************/
//sfr INT_CLKO = 0x8F; //附加的 SFR WAKE_CLKO (地址：0x8F)
/*
7 6 5 4 3 2 1 0 Reset Value
- EX4 EX3 EX2 - T2CLKO T1CLKO T0CLKO 0000,0000B
b6 - EX4 : 外中斷INT4允許
b5 - EX3 : 外中斷INT3允許
b4 - EX2 : 外中斷INT2允許
b2 - T1CLKO : 允許 T2 溢出脈沖在P3.0腳輸出，Fck1 = 1/2 T1 溢出率
b1 - T1CLKO : 允許 T1 溢出脈沖在P3.4腳輸出，Fck1 = 1/2 T1 溢出率
b0 - T0CLKO : 允許 T0 溢出脈沖在P3.5腳輸出，Fck0 = 1/2 T0 溢出率
*/
#define LVD_InterruptEnable() ELVD = 1
#define LVD_InterruptDisable() ELVD = 0
//sfr WKTCL = 0xAA; //STC11F\10和STC15系列喚醒定時器低字節
//sfr WKTCH = 0xAB; //STC11F\10和STC15系列喚醒定時器高字節
// B7 B6 B5 B4 B3 B2 B1 B0 B7 B6 B5 B4 B3 B2 B1 B0
// WKTEN S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0 n * 560us
#define WakeTimerDisable() WKTCH &= 0x7f //WKTEN = 0 禁止睡眠喚醒定時器
#define WakeTimerSet(scale) WKTCL = (scale) % 256,WKTCH = (scale) / 256 | 0x80 //WKTEN = 1 允許睡眠喚醒定時器
//sfr CLK_DIV = 0x97; //Clock Divder 系統時鐘分頻 - - - - - CLKS2 CLKS1 CLKS0 xxxx,x000
#define SYSTEM_CLK_1T() CLK_DIV &= ~0x07 //default
#define SYSTEM_CLK_2T() CLK_DIV = (CLK_DIV & ~0x07) | 1
#define SYSTEM_CLK_4T() CLK_DIV = (CLK_DIV & ~0x07) | 2
#define SYSTEM_CLK_8T() CLK_DIV = (CLK_DIV & ~0x07) | 3
#define SYSTEM_CLK_16T() CLK_DIV = (CLK_DIV & ~0x07) | 4
#define SYSTEM_CLK_32T() CLK_DIV = (CLK_DIV & ~0x07) | 5
#define SYSTEM_CLK_64T() CLK_DIV = (CLK_DIV & ~0x07) | 6
#define SYSTEM_CLK_128T() CLK_DIV = CLK_DIV | 7
#define MCLKO_P54_None() CLK_DIV &= ~0xc0 //主時鐘不輸出
#define MCLKO_P54_DIV1() CLK_DIV = (CLK_DIV & ~0xc0) | 0x40 //主時鐘不分頻輸出
#define MCLKO_P54_DIV2() CLK_DIV = (CLK_DIV & ~0xc0) | 0x80 //主時鐘2分頻輸出
#define MCLKO_P54_DIV4() CLK_DIV = CLK_DIV | 0xc0 //主時鐘4分頻輸出
#define MCLKO_P34_None() CLK_DIV &= ~0xc0 //主時鐘不輸出
#define MCLKO_P34_DIV1() CLK_DIV = (CLK_DIV & ~0xc0) | 0x40 //主時鐘不分頻輸出
#define MCLKO_P34_DIV2() CLK_DIV = (CLK_DIV & ~0xc0) | 0x80 //主時鐘2分頻輸出
#define MCLKO_P34_DIV4() CLK_DIV = CLK_DIV | 0xc0 //主時鐘4分頻輸出
//sfr BUS_SPEED = 0xA1; //Stretch register - - - - - - EXRTS1 EXRTSS0 xxxx,xx10
#define BUS_SPEED_1T() BUS_SPEED = 0
#define BUS_SPEED_2T() BUS_SPEED = 1
#define BUS_SPEED_4T() BUS_SPEED = 2
#define BUS_SPEED_8T() BUS_SPEED = 3
/* interrupt vector */
#define INT0_VECTOR 0
#define TIMER0_VECTOR 1
#define INT1_VECTOR 2
#define TIMER1_VECTOR 3
#define UART1_VECTOR 4
#define ADC_VECTOR 5
#define LVD_VECTOR 6
#define PCA_VECTOR 7
#define UART2_VECTOR 8
#define SPI_VECTOR 9
#define INT2_VECTOR 10
#define INT3_VECTOR 11
#define TIMER2_VECTOR 12
#define INT4_VECTOR 16
#define UART3_VECTOR 17
#define UART4_VECTOR 18
#define TIMER3_VECTOR 19
#define TIMER4_VECTOR 20
#define TRUE 1
#define FALSE 0
//=============================================================
//========================================
#define PolityLow 0 //低優先級中斷
#define PolityHigh 1 //高優先級中斷
//========================================
#define MCLKO_None 0
#define MCLKO_DIV1 1
#define MCLKO_DIV2 2
#define MCLKO_DIV4 3
#define ENABLE 1
#define DISABLE 0
#define STC15F_L2K08S2 8
#define STC15F_L2K16S2 16
#define STC15F_L2K24S2 24
#define STC15F_L2K32S2 32
#define STC15F_L2K40S2 40
#define STC15F_L2K48S2 48
#define STC15F_L2K56S2 56
#define STC15F_L2K60S2 60
#define IAP15F_L2K61S2 61
#endif

復制代碼

欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136