高清无码禁看视频,免费人成视频在线观看日本,一级二级三级黄色片

/****************************************Copyright (c)****************************************************
**--------------File Info---------------------------------------------------------------------------------
** Descriptions: The GPIO LED application function
**
**--------------------------------------------------------------------------------------------------------
** Created by: AVRman
** Version: v1.0
** Descriptions: The original version
**
**--------------------------------------------------------------------------------------------------------
** Modified by:
** Modified date:
** Version:
** Descriptions:
**
*********************************************************************************************************/
/* Includes ------------------------------------------------------------------*/
#include "stm32f10x.h"
#include "LCD_12864.H"
#include "stm32f10x_it.h"
#include <stdio.h>
uint8_t i = 0;
/* Private functions ---------------------------------------------------------*/
void GPIO_Configuration(void);
void TIM_Configuration(void);
void RCC_Configuration(void);
void NVIC_Configuration(void);
/*******************************************************************************
* Function Name : Delay
* Description : Delay Time
* Input : - nCount: Delay Time
* Output : None
* Return : None
* Attention : None
*******************************************************************************/
void Delay (uint32_t nCount)
{
for(; nCount != 0; nCount--);
}
void SysClock_Init(void)
{
ErrorStatus HSEStartUpStatus;
RCC_DeInit();
RCC_HSEConfig(RCC_HSE_ON);
HSEStartUpStatus = RCC_WaitForHSEStartUp();
if(HSEStartUpStatus == SUCCESS){
FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);
FLASH_SetLatency(FLASH_Latency_2);
RCC_HCLKConfig(RCC_SYSCLK_Div1);
RCC_PCLK2Config(RCC_HCLK_Div1);
RCC_PCLK1Config(RCC_HCLK_Div2);
RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);
RCC_PLLCmd(ENABLE);
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET){
;
}
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
while(RCC_GetSYSCLKSource() != 0x08){
;
}
}
}
/*******************************************************************************
* Function Name :
* Description : Programme
* Input : None
* Output : None
* Return : None
* Attention : None
*******************************************************************************/
int main(void)
{
char str[20];
SysClock_Init(); // 初始化系統時鐘 72MHZ
GPIO_Configuration();
NVIC_Configuration();
RCC_Configuration();
TIM_Configuration();
/* Infinite loop */
lcd_init(); //初始化LCD12864
while (1){
if(CH2_finish)
{ //多放幾個空格，不留痕跡
sprintf( str, "%d ", (tmp16_CH2) ); //計數值
lcd_char(0x90,str);
sprintf( str, "%.1f Hz. ", (8000000.0/tmp16_CH2) ); //保留一位小數
lcd_char(0x88,str);
CH2_finish = 0;
i++;
Delay(0X01FFFF);
}
lcd_char(0x80, "脈沖波捕捉測試");
i++;
Delay(0X01FFFF);
}
}
/*******************************************************************************
* Function Name : GPIO_Configuration
* Description : Configure GPIO Pin
* Input : None
* Output : None
* Return : None
* Attention : None
*******************************************************************************/
void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
/**
* LED1 -> PC6 , LED2 -> PC7,LED1 -> PC8 , LED2 -> PC9
*/ //管腳配置
RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOE , ENABLE); //要有這個
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5 | GPIO_Pin_6;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOE, &GPIO_InitStructure);
//no 12864 pin
//TIM4對應 4路捕捉腳PB6~PB9
//信號發生器用有夾子的一組才有效
//GPIO_PinRemapConfig(GPIO_Remap_TIM4, ENABLE); //管腳重映射
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6|GPIO_Pin_7 | GPIO_Pin_8 | GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;//浮空輸入
GPIO_Init(GPIOB, &GPIO_InitStructure);
}
void TIM_Configuration(void)
{
TIM_ICInitTypeDef TIM_ICInitStructure;
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure; // TIM4 時基
///TIM4
TIM_DeInit(TIM4);
/*TIM_Prescaler = (720-1)；大于2hz小于1khz比較準，計數值<=85 ：10us記一次數
TIM_Prescaler = (18-1)：大于900hz 小于40Khz : 1/4us記一次數
TIM_Prescaler = (9-1)：大于900hz 小于50Khz ：1/8us記一次數
計數值小于100都不怎么準了
*/
//為自動重裝值，與普通單片機一樣,滿值基本不溢出65535
TIM_TimeBaseStructure.TIM_Period = 0xffff;
//預分頻值, 使TIMx_CLK=100KHz ，系統時鐘運行于72M時720分頻，定時器運行于100KHZ，即10us每分度
TIM_TimeBaseStructure.TIM_Prescaler = (9-1);
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1; //輸入時鐘不分頻
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //向上計數
TIM_TimeBaseInit(TIM4, &TIM_TimeBaseStructure);
//ch2
// TIM_ICInitStructure.TIM_ICMode = TIM_ICMode_ICAP; //輸入捕捉方式
TIM_ICInitStructure.TIM_Channel = TIM_Channel_2;// //輸入通道
TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising; //捕捉上升沿
TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI; //捕捉中斷
TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1; //捕捉不分頻
TIM_ICInitStructure.TIM_ICFilter = 0x0; //捕捉輸入不濾波
TIM_ICInit(TIM4, &TIM_ICInitStructure);
//TIM_SelectInputTrigger(TIM4, TIM_TS_TI2FP2); //選擇IC2為始終觸發源
//TIM_SelectSlaveMode(TIM4, TIM_SlaveMode_Reset);//TIM從模式：觸發信號的上升沿重新初始化計數器和觸發寄存器的更新事件
//TIM_SelectMasterSlaveMode(TIM4, TIM_MasterSlaveMode_Enable); //啟動定時器的被動觸發
//ch2
//TIM_ICInitStructure.TIM_Channel = TIM_Channel_2 ;//| TIM_Channel_2; //輸入通道
// TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising; //捕捉上升沿
//
// TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI; //捕捉中斷
//
// TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1; //捕捉不分頻
//
// TIM_ICInitStructure.TIM_ICFilter = 0x0; //捕捉輸入不濾波
// TIM_ICInit(TIM4, &TIM_ICInitStructure);
//
// TIM_ICInitStructure.TIM_Channel = TIM_Channel_3 ;//TIM_Channel_2; //輸入通道
// //ch3
// TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising; //捕捉上升沿
//
// TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI; //捕捉中斷
//
// TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1; //捕捉不分頻
//
// TIM_ICInitStructure.TIM_ICFilter = 0x0; //捕捉輸入不濾波
// TIM_ICInit(TIM4, &TIM_ICInitStructure);
//
// TIM_ICInitStructure.TIM_Channel = TIM_Channel_4 ;//| TIM_Channel_2; //輸入通道
// //ch4
// TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_BothEdge; //捕捉上升沿
//
// TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI; //捕捉中斷
//
// TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1; //捕捉不分頻
//
// TIM_ICInitStructure.TIM_ICFilter = 0xf; //捕捉輸入不濾波
// TIM_ICInit(TIM4, &TIM_ICInitStructure);
// /* TIM enable counter */
TIM_Cmd(TIM4, ENABLE);
/* Enable the CC2 Interrupt Request */
// TIM_ITConfig(TIM4, TIM_IT_CC1, ENABLE);
TIM_ITConfig(TIM4, TIM_IT_CC2, ENABLE);
// TIM_ITConfig(TIM4, TIM_IT_CC3, ENABLE);
// TIM_ITConfig(TIM4, TIM_IT_CC4, ENABLE); //第四路有問題
}
void RCC_Configuration(void)
{
SystemInit();
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA
|RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC
|RCC_APB2Periph_GPIOD |RCC_APB2Periph_GPIOE
| RCC_APB2Periph_AFIO , ENABLE );
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE );
}
void NVIC_Configuration(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
/* Configure the NVIC Preemption Priority Bits */
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0); //設置優先級分組：先占優先級0位,從優先級4位
/* Enable the TIM4 global Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = TIM4_IRQn; //TIM4中斷
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; //先占優先級0級
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; //從優先級3級
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能
NVIC_Init(&NVIC_InitStructure); //根據NVIC_InitStruct中指定的參數初始化外設NVIC寄存器
}
#ifdef USE_FULL_ASSERT
/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t* file, uint32_t line)
{
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* Infinite loop */
while (1)
{
}
}
#endif
/*********************************************************************************************************
END FILE
*********************************************************************************************************/

復制代碼

欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136